Serial Number
QT
2.4L
45kW
Model: 005262-0
STANDBY GENERATOR
OWNER'S MANUAL
A new standard of reliability
—CAUTION—
ONLY QUALIFIED ELECTRICIANS OR CONTRACTORS SHOULD ATTEMPT INSTALLATION!
This manual should remain with the unit.
. 0 v 0 2 / 0 6 e v r 0 4 C 4 o R e
. 0 G 0 t N 2 r 0 o a 2 P
Download from Www.Somanuals.com. All Manuals Search And Download.
Standby Generator Sets
Important Safety Instructions
SAVE THESE INSTRUCTIONS – The manufacturer suggests that these rules for safe
operation be copied and posted in potential hazard areas. Safety should be stressed to all
operators, potential operators, and service and repair technicians for this equipment.
GENERAL HAZARDS
WARNING:
• For safety reasons, the manufacturer recommends
that this equipment be installed, serviced and
repaired by an Authorized Service Dealer or other
competent, qualified electrician or installation tech-
nician who is familiar with applicable codes, stan-
dards and regulations. The operator also must
comply with all such codes, standards and regula-
tions.
The engine exhaust from this product
contains chemicals known to the state
of California to cause cancer, birth
defects or other reproductive harm.
WARNING:
This product contains or emits chemicals
known to the state of California to cause
• Installation, operation, servicing and repair of this
(and related) equipment must always comply with
applicable codes, standards, laws and regulations.
Adhere strictly to local, state and national electri-
cal and building codes. Comply with regulations
the Occupational Safety and Health Administration
(OSHA) has established. Also, ensure that the
generator is installed, operated and serviced in
accordance with the manufacturer’s instructions
and recommendations. Following installation, do
nothing that might render the unit unsafe or in
noncompliance with the aforementioned codes,
standards, laws and regulations.
• The engine exhaust fumes contain carbon monox-
ide gas, which can be DEADLY. This dangerous gas,
if breathed in sufficient concentrations, can cause
unconsciousness or even death. For that reason,
adequate ventilation must be provided. Exhaust
gases must be piped safely away from any building
or enclosure that houses the generator to an area
where people, animals, etc., will not be harmed.
This exhaust system must be installed properly, in
strict compliance with applicable codes and stan-
dards.
cancer, birth defects or other reproductive harm.
Study these SAFETY RULES carefully before install-
ing, operating or servicing this equipment. Become
familiar with this Owner’s Manual and with the unit.
The generator can operate safely, efficiently and reli-
ably only if it is properly installed, operated and
maintained. Many accidents are caused by failing to
follow simple and fundamental rules or precautions.
The manufacturer cannot anticipate every possible
circumstance that might involve a hazard. The warn-
ings in this manual, and on tags and decals affixed
to the unit are, therefore, not all inclusive. If a pro-
cedure, work method or operating technique is used
that the manufacturer does not specifically recom-
mend, ensure that it is safe for others. Also make
sure the procedure, work method or operating tech-
nique utilized does not render the generator unsafe.
DANGER
Despite the safe design of this generator,
operating this equipment imprudently, neglect-
ing its maintenance or being careless can cause
possible injury or death. Permit only responsible
and capable persons to install, operate or main-
tain this equipment.
• Keep hands, feet, clothing, etc., away from drive
belts, fans, and other moving or hot parts. Never
remove any drive belt or fan guard while the unit
is operating.
• Adequate, unobstructed flow of cooling and venti-
lating air is critical in any room or building hous-
ing the generator to prevent buildup of explosive
gases and to ensure correct generator operation.
Do not alter the installation or permit even partial
blockage of ventilation provisions, as this can seri-
ously affect safe operation of the generator.
• Keep the area around the generator clean and
uncluttered. Remove any materials that could
become hazardous.
Potentially lethal voltages are generated by
these machines. Ensure all steps are taken to
render the machine safe before attempting to
work on the generator.
Parts of the generator are rotating and/or hot
during operation. Exercise care near running
generators.
• When working on this equipment, remain alert
at all times. Never work on the equipment when
physically or mentally fatigued.
• Inspect the generator regularly, and promptly
repair or replace all worn, damaged or defective
parts using only factory-approved parts.
. 0 v 0 8 / 0 5
e t y S 0 a 0 f 1 R e
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Standby Generator Sets
Important Safety Instructions
• Before performing any maintenance on the gen-
• Generators installed with an automatic transfer
switch will crank and start automatically when
normal (utility) source voltage is removed or is
below an acceptable preset level. To prevent such
automatic start-up and possible injury to person-
nel, disable the generator’s automatic start circuit
(battery cables, etc.) before working on or around
the unit. Then, place a “Do Not Operate” tag on
the generator control panel and on the transfer
switch.
erator, disconnect its battery cables to prevent
accidental start-up. Disconnect the cable from the
battery post indicated by a NEGATIVE, NEG or (–)
first. Reconnect that cable last.
• Never use the generator or any of its parts as a
step. Stepping on the unit can stress and break
parts, and may result in dangerous operating con-
ditions from leaking exhaust gases, fuel leakage,
oil leakage, etc.
• In case of accident caused by electric shock, imme-
diately shut down the source of electrical power.
If this is not possible, attempt to free the victim
from the live conductor. AVOID DIRECT CONTACT
WITH THE VICTIM. Use a nonconducting imple-
ment, such as a dry rope or board, to free the vic-
tim from the live conductor. If the victim is uncon-
scious, apply first aid and get immediate medical
help.
• Never wear jewelry when working on this equip-
ment. Jewelry can conduct electricity resulting in
electric shock, or may get caught in moving com-
ponents causing injury.
ELECTRICAL HAZARDS
• All generators covered by this manual produce
dangerous electrical voltages and can cause fatal
electrical shock. Utility power delivers extremely
high and dangerous voltages to the transfer switch
as well as the standby generator. Avoid contact
with bare wires, terminals, connections, etc., on
the generator as well as the transfer switch, if
applicable. Ensure all appropriate covers, guards
and barriers are in place before operating the gen-
erator. If work must be done around an operating
unit, stand on an insulated, dry surface to reduce
shock hazard.
FIRE HAZARDS
• Do not handle any kind of electrical device while
standing in water, while barefoot, or while hands or
feet are wet. DANGEROUS ELECTRICAL SHOCK
MAY RESULT.
• If personnel must stand on metal or concrete while
installing, operating, servicing, adjusting or repair-
ing this equipment, place insulative mats over a
dry wooden platform. Work on the equipment only
while standing on such insulative mats.
• Keep a fire extinguisher near the generator at all
times. Do NOT use any carbon tetra-chloride type
extinguisher. Its fumes are toxic, and the liquid
can deteriorate wiring insulation. Keep the extin-
guisher properly charged and be familiar with its
use. If there are any questions pertaining to fire
extinguishers, consult the local fire department.
• The National Electrical Code (NEC) requires the
frame and external electrically conductive parts
of the generator to be connected to an approved
earth ground. This grounding will help prevent
dangerous electrical shock that might be caused
by a ground fault condition in the generator set or
by static electricity. Never disconnect the ground
wire.
• Wire gauge sizes of electrical wiring, cables and
cord sets must be adequate to handle the maxi-
mum electrical current (ampacity) to which they
will be subjected.
• Before installing or servicing this (and related)
equipment, make sure that all power voltage
supplies are positively turned off at their source.
Failure to do so will result in hazardous and pos-
sibly fatal electrical shock.
• Connecting this unit to an electrical system nor-
mally supplied by an electric utility shall be by
means of a transfer switch so as to isolate the
generator electric system from the electric utility
distribution system when the generator is operat-
ing. Failure to isolate the two electric system power
sources from each other by such means will result
in damage to the generator and may also result
in injury or death to utility power workers due to
backfeed of electrical energy.
EXPLOSION HAZARDS
• Properly ventilate any room or building housing
the generator to prevent build-up of explosive gas.
• Do not smoke around the generator. Wipe up any
fuel or oil spills immediately. Ensure that no com-
bustible materials are left in the generator com-
partment, or on or near the generator, as FIRE or
EXPLOSION may result. Keep the area surround-
ing the generator clean and free from debris.
• These generator sets may operate using one of
several types of fuels. All fuel types are potentially
FLAMMABLE and/or EXPLOSIVE and should be
handled with care. Comply with all laws regulat-
ing the storage and handling of fuels. Inspect the
unit’s fuel system frequently and correct any leaks
immediately. Fuel supply lines must be prop-
erly installed, purged and leak tested according to
applicable fuel-gas codes before placing this equip-
ment into service.
• Diesel fuels are highly FLAMMABLE. Gaseous
fluids such as natural gas and liquid propane
(LP) gas are extremely EXPLOSIVE. Natural gas
is lighter than air, and LP gas is heavier than air;
install leak detectors accordingly.
. 0 v 0 8 / 0 5
e t y S 0 a 0 f 1 R e
1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Standby Generator Sets
Important Safety Instructions
INTRODUCTION
This symbol points out potential fire hazard.
Thank you for purchasing this model of the standby
generator set product line.
This symbol points out potential electrical shock
hazard.
Every effort was expended to make sure that the
information and instructions in this manual were
both accurate and current at the time the manual was
written. However, the manufacturer reserves the right
to change, alter or otherwise improve this product(s)
at any time without prior notice.
The operator is responsible for proper and safe use
of the equipment. The manufacturer strongly recom-
mends that the operator read this Owner's Manual
and thoroughly understand all instructions before
using this equipment. The manufacturer also strong-
ly recommends instructing other users to properly
start and operate the unit. This prepares them if they
need to operate the equipment in an emergency.
READ THIS MANUAL THOROUGHLY
If any portion of this manual is not understood, con-
tact the nearest Authorized Service Dealer for start-
ing, operating and servicing procedures.
OPERATION AND MAINTENANCE
It is the operator's responsibility to perform all safety
checks, to make sure that all maintenance for safe
operation is performed promptly, and to have the
equipment checked periodically by an Authorized
Service Dealer. Normal maintenance service and
replacement of parts are the responsibility of the
owner/operator and, as such, are not considered
defects in materials or workmanship within the terms
of the warranty. Individual operating habits and usage
contribute to the need for maintenance service.
Throughout this publication, and on tags and
decals affixed to the generator, DANGER, WARNING,
CAUTION and NOTE blocks are used to alert person-
nel to special instructions about a particular service
or operation that may be hazardous if performed
incorrectly or carelessly. Observe them carefully.
Their definitions are as follows:
DANGER
After this heading, read instructions that, if not
strictly complied with, will result in personal injury
or property damage.
Proper maintenance and care of the generator ensure
a minimum number of problems and keep operating
expenses at a minimum. See an Authorized Service
Dealer for service aids and accessories.
Operating instructions presented in this manual
assume that the standby electric system has been
installed by an Authorized Service Dealer or other
competent, qualified contractor. Installation of this
equipment is not a “do-it-yourself” project.
After this heading, read instructions that, if not
strictly complied with, may result in personal
injury or property damage.
HOW TO OBTAIN SERVICE
After this heading, read instructions that, if not
strictly complied with, could result in damage to
equipment and/or property.
When the generator requires servicing or repairs,
simply contact an Authorized Service Dealer for
assistance. Service technicians are factory-trained
and are capable of handling all service needs.
NOTE:
After this heading, read explanatory statements
that require special emphasis.
When contacting an Authorized Service Dealer or the
factory about parts and service, always supply the
complete model number of the unit as given on the
front cover of this manual or on the DATA LABEL
affixed to the unit.
These safety warnings cannot eliminate the hazards
that they indicate. Common sense and strict compli-
ance with the special instructions while performing
the service are essential to preventing accidents.
Four commonly used safety symbols accompany the
DANGER, WARNING and CAUTION blocks. The type
of information each indicates is as follows:
AUTHORIZED SERVICE DEALER LOCATION
To locate the nearest AUTHORIZED
This symbol points out important safety infor-
SERVICE DEALER, please call this number:
mation that, if not followed, could endanger
1-800-333-1322
or locate us on the web at:
personal safety and/or property of others.
This symbol points out potential explosion
hazard.
www.generac.com
. 0 v 0 8 / 0 5
e t y S 0 a 0 f 1 R e
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Standby Generator Sets
General Information
NOTE:
IDENTIFICATION RECORD
For actual information related to this particular
model, please refer to the Manual Drawing Listing
located at the end of this manual, or to the data
label affixed to the unit.
DATA LABEL
Every generator set has a DATA LABEL that contains
important information pertinent to the generator. The
data label, which can be found attached to the gen-
erator’s lower connection box, lists the unit’s serial
number and its rated voltage, amps, wattage capacity,
phase, frequency, rpm, power factor, etc.
Generator Model and Serial Number
This number is the key to numerous engineering and
manufacturing details pertaining to your unit. Always
supply this number when requesting service, order-
ing parts or seeking information.
Data Label
GENERATOR SET DATA
SERIAL
MADE IN USA
MODEL
RATED KVA
PHASE
RATED KW
RATED AMPS
RATED VOLTAGE
POWER FACTOR
ENGINE RPM
HERTZ
ALT RPM
PRODUCTION DATE
ALTERNATOR SUBTRANSIENT REACTANCE
ALTERNATOR TRANSIENT REACTANCE
CLASS
ROTOR
STATOR WINDING INSULATION AT 25°C AMBIENT
GENERAC POWER SYSTEMS, INC.
WAUKESHA, WI
. A v 1 2 / 0 5
I d e n t y 0 0 2 R e
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Standby Generator Sets
Equipment Description
EQUIPMENT DESCRIPTION
COOLANT RECOMMENDATIONS
This equipment is a revolving field, alternating cur-
rent generator set. It is powered by a gaseous fueled
engine operating at 1800 rpm for 4-pole direct drive
units, 3600 rpm for 2-pole direct drive units and
2300 - 3000 rpm for quiet drive gear units. See the
Specifications section for exact numbers. The unit
comes complete with a sound attenuated enclosure,
internally mounted muffler, control console, main-
line circuit breaker, battery charger, and protective
alarms as explained in the following paragraph.
Use a mixture of half low silicate ethylene glycol
base anti-freeze and deionized water. Cooling system
capacity is listed in the specifications. Use only deion-
ized water and only low silicate anti-freeze. If desired,
add a high quality rust inhibitor to the recommended
coolant mixture. When adding coolant, always add
the recommended 50-50 mixture.
Do not use any chromate base rust inhibitor
All AC connections, including the power leads from
the alternator, 120 volt battery charger input and
control connections to the transfer switch are avail-
able in the main connection box.
with ethylene glycol base anti-freeze or chro-
mium hydroxide (“green slime”) forms and will
cause overheating. Engines that have been oper-
ated with a chromate base rust inhibitor must
be chemically cleaned before adding ethylene
glycol base anti-freeze. Using any high silicate
anti-freeze boosters or additives will also cause
overheating. The manufacturer also recommends
that any soluble oil inhibitor is NOT used for this
equipment.
The generator incorporates the following generator
features:
• Rotor and Stator insulation is Class H rated as
defined by NEMA MG1-32.6, NEMA MG1-1.66.
The generator is self ventilated and drip-proof con-
structed.
• The voltage waveform deviation, total harmonic
content of the AC waveform and telephone influ-
ence factor have been evaluated and are acceptable
according to NEMA MG1-32.
DANGER
Do not remove the radiator pressure cap while
the engine is hot or serious burns from boiling
liquid or steam could result.
Ethylene glycol base antifreeze is poisonous.
Do not use mouth to siphon coolant from the
radiator, recovery bottle or any container. Wash
hands thoroughly after handling. Never store
used antifreeze in an open container because
animals are attracted to the smell and taste of
antifreeze even though it is poisonous to them.
ENGINE OIL RECOMMENDATIONS
The unit has been filled with 15W-40 engine oil at
the factory. Use a high-quality detergent oil classified
“For Service CC, SD, SE, SF.” Detergent oils keep the
engine cleaner and reduce carbon deposits. Use oil
having the following SAE viscosity rating, based on
the ambient temperature range anticipated before the
next oil change:
Temperature
Above 80° F (27° C)
32° to 80° F (0° to 27° C)
Below 32° F (0° C)
Oil Grade (Recommended)
SAE 30W or 15W-40
SAE 20W-20 or 15W-40
See Note
Any attempt to crank or start the engine before
it has been properly serviced with the recom-
mended oil may result in an engine failure.
NOTE:
For temperatures below 32° F, it is strongly recom-
mended to use the optional Cold Weather Start Kit
(part number listed in the Specification Section).
The oil grade for temperatures below 32° F is 5W-
30 synthetic oil.
. 0 v 0 8 / 0 5
E q u i p 0 0 1 R e
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Standby Generator Sets
Engine Protective Devices
OVERCRANK SHUTDOWN
ENGINE PROTECTIVE DEVICES
The standby generator may be required to operate for
long periods of time without an operator on hand to
monitor such engine conditions as coolant tempera-
ture, oil pressure or rpm. For that reason, the engine
has several devices designed to protect it against
potentially damaging conditions by automatically
shutting down the unit when the oil pressure is too
low, the coolant temperature is too high, the coolant
level is too low, or the engine is running too fast.
After a prespecified duration of cranking, this func-
tion ends the cranking if the engine has failed to
start. The overcrank LED will turn ON. Turn OFF the
AUTO/OFF/MANUAL switch, then turn switch back to
AUTO to reset the generator control board.
NOTE:
If the fault is not corrected, the overcrank feature
will continue to activate.
NOTE:
Approximate Crank Cycle Times
• 15 seconds ON
• 7 seconds OFF
• 7 seconds ON
Engine protective switches and sensors are men-
tioned here for the reader’s convenience. Also
refer to the applicable control panel manual for
additional automatic engine shutdown informa-
tion.
• 7 seconds OFF
• Repeat for 45 seconds
Approximately 90 seconds total.
HIGH COOLANT TEMPERATURE SWITCH
This switches contacts close if the temperature should
exceed approximately 140° C (284° F), initiating an
engine shutdown. The generator will automatically
restart and the LED will reset once the temperature
has returned to a safe operating level.
OVERSPEED SHUTDOWN
A speed circuit controls engine cranking, start-up,
operation and shutdown. Engine speed signals are
delivered to the circuit board whenever the unit is
running. Should the engine overspeed above a safe,
preset value, the circuit board initiates an automatic
engine shutdown. Contact the nearest Authorized
Dealer if this failure occurs.
LOW COOLANT LEVEL SENSOR
Should the engine coolant level drop below the level
of the high coolant temperature switch, it is possible
for the engine to overheat without automatic shut-
down. To prevent such overheating, the engine has a
low coolant level sensor. If the level of engine coolant
drops below the level of the low coolant level sensor,
the engine automatically shuts down.
RPM SENSOR LOSS SHUTDOWN
If the speed signal to the control panel is lost, engine
shutdown will occur.
DC FUSE
LOW OIL PRESSURE SWITCH
This fuse is located inside of the control panel. It
protects the panel wiring and components from
damaging overload. Always remove this fuse before
commencing work on the generator. The unit will
not start or crank if the fuse is blown. Replace the
fuse with one of the same size, type, and rating. (See
the exploded views and parts lists at the end of this
manual for replacement part number.)
This switch has normally closed contacts that are
held open by engine oil pressure during cranking and
operating. Should oil pressure drop below the 8 psi
range, switch contacts close, and the engine shuts
down. The unit should not be restarted until oil is
added, and the AUTO/OFF/MANUAL switch must be
turned to OFF and then back to AUTO.
. 0 v 0 8 / 0 5
E n g P r o t 0 0 1 R
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Standby Generator Sets
Fuel Systems
PROPANE VAPOR WITHDRAWAL FUEL SYSTEM
FUEL SYSTEM
This type of system utilizes the vapors formed above
the liquid fuel in the supply tank. Approximately 10
to 20 percent of the tank capacity is needed for fuel
expansion from the liquid to the vapor state. The
vapor withdrawal system is generally best suited for
smaller engines that require less fuel. The installer
should be aware of the following:
FUEL REQUIREMENTS
The standby generator may be equipped with one of
the following fuel systems:
• Natural gas fuel system
• Propane vapor (PV) fuel system
The Manual Drawing Listing that is affixed to the
unit includes the “Identification Code,” which may be
used to identify the type of fuel system installed on
the unit.
• The natural gas and LP gas systems are similar.
However, the natural gas system delivers gas at a
pressure of approximately five inches water col-
umn to the carburetor.
Recommended fuels should have a Btu content of at
least 1,000 Btus per cubic foot for natural gas; or at
least 2,520 Btus per cubic foot for LP gas. Ask the
fuel supplier for the Btu content of the fuel.
• When ambient temperatures are low and engine
fuel consumption is high, the vapor withdrawal
system may not function efficiently.
• Ambient temperatures around the supply tank
must be high enough to sustain adequate vaporiza-
tion, or the system will not deliver the needed fuel
volume.
• In addition to the cooling effects of ambient air, the
vaporization process itself provides an additional
cooling effect.
Required fuel pressure for natural gas is 5 inches
to 14 inches water column (0.18 to 0.5 psi); and
for liquid propane, 5 inches to 14 inches of water
column (0.18 to 0.5 psi).
NOTE:
Any piping used to connect the generator to the
fuel supply should be of adequate size to ensure
the fuel pressure NEVER drops below five inches
water column for natural gas or 5 inches water
column for propane vapor for all load ranges.
LP FUEL SYSTEM
LP is supplied as a liquid in pressure tanks. It is
usually made up of propane, butane, or a mixture of
the two gases. Propane tends to vaporize readily even
at temperatures as low as -20° F (-29° C). However,
butane reverts to its liquid state when temperatures
drop below 32° F (0° C).
NOTE:
It is the responsibility of the installer to make sure
that only the correct recommended fuel is sup-
plied to the generator fuel system. Thereafter, the
owner/operator must make certain that only the
proper fuel is supplied.
LP in a liquid withdrawal system must be converted
to its gaseous state before it is introduced into the
engine carburetor. A vaporizer-converter is generally
used to accomplish this. In such a converter, heated
engine coolant is ported through the converter to
provide the necessary heat for conversion of the fuel
from a liquid to a gaseous state.
NATURAL GAS FUEL SYSTEM
Natural gas is supplied in its vapor state. In most
cases, the gas distribution company provides piping
from the main gas distribution line to the standby
generator site. The following information applies to
natural gas fuel systems.
• Gas pressure in a building is usually regulated by
national, state and local codes.
• To reduce gas pressure to a safe level before
the gas enters a building, a primary regulator is
needed. The natural gas supplier may or may not
supply such a regulator.
• It is the responsibility of the gas supplier to make
sure sufficient gas pressure is available to operate
the primary regulator.
• Gas pressure at the inlet to the fuel shutoff sole-
noid should not exceed approximately 14 inches
water column (0.5 psi). Optimum pressure at the
fuel shutoff solenoid is 11 inches water column
(0.4 psi).
. 0 v 0 8 / 0 5
F u e l S y s 0 0 1 R
5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Standby Generator Sets
Specifications
COOLING SYSTEM
SPECIFICATIONS
Type...................................................Pressurized Closed Recovery
Water Pump.................................................................... Belt Driven
Fan Speed.........................................................................2150 rpm
Fan Diameter.....................................................................22 inches
Fan Mode ................................................................................Puller
Air Flow (inlet air including alternator and
GENERATOR
Type............................................................................. Synchronous
Rotor Insulation ................................................................... Class H
Stator Insulation .................................................................. Class H
Total Harmonic Distortion..........................................................<5%
Telephone Interference Factor (TIF)..........................................< 50
Alternator Output Leads 3-phase........................................... 4-wire
Bearings .........................................................................Sealed Ball
Coupling .......................................................................Flexible Disc
Load Capacity (Standby Rating) ............................................45kW*
3
combustion air)...........................................................2725 ft /min.
Coolant Capacity........................................................ (3.0 U.S. gal.)
Heat Rejection to Coolant ..........................................173,000 Btu/h
Maximum Operating Air Temp. on Radiator ..............60° C (150° F)
Maximum Ambient Temperature................................50° C (140° F)
* NOTE: Generator rating and performance in accordance with ISO8528-5, BS5514, SAE J1349,
ISO3046 and DIN 6271 Standards. KW rating is based on LPG fuel and may derate with natural
FUEL SYSTEM
gas.
Type of Fuel.........................................Natural Gas, Propane Vapor
Carburetor ...................................................................... Down Draft
Secondary Fuel Regulator .................................................Standard
Fuel Shut-off Solenoid........................................................Standard
Operating Fuel Pressure ...................... 5 in. - 14 in. Water Column
Excitation System....................................................................Direct
Generator Output Voltage/kW - 60 Hz
120/240V, 1-phase, 1.0 pf
120/208V, 3-phase, 0.8 pf
kW
45
45
45
Amp CB Size
188
156
68
200
175
80
277/480V, 3-phase, 0.8 pf
Generator Locked Rotor KVA Available @ Voltage Dip of 35%
Single-phase or 208, 3-phase............................................ 80 KVA
480V, 3-phase .................................................................. 100 KVA
Fuel Consumption - ft3/hr (Natural Gas/LPV)
Exercise
Cycle
102/40.4
25%
Load
50%
Load
373/148 520/206.3 720/286
75%
100%
Load
Load
194/77.1
ENGINE
Make................................................................................... Generac
Model..................................................................................... In Line
Cylinders and Arrangement............................................................ 4
Displacement.......................................................................2.4 Liter
Bore...................................................................................... 3.41 in.
Stroke ................................................................................... 3.94 in.
Compression Ratio...............................................................8.5-to-1
Air Intake System ...............................................Naturally Aspirated
Valve Seats....................................................................... Hardened
Lifter Type.......................................................................... Hydraulic
ELECTRICAL SYSTEM
Battery Charge Alternator ............................................12V, 30 Amp
Static Battery Charger............................................................2 Amp
Recommended Battery...................................... Group 26, 525CCA
System Voltage.....................................................................12 Volts
Voltage Regulator
Type.................................................................................. Electronic
Sensing........................................................................ Single-phase
Regulation ................................................................................ 1%
Features .................................................V/F Adjustable, Adjustable
Voltage and Gain LED Indicators
Engine Parameters
Rated Synchronous RPM..............................................60 Hz, 3600
HP at rated kW..................................................................60 Hz, 71
Power Adjustment for Ambient Conditions
Temperature Deration
3% for every 10° C above °C..................................................... 25
1.65% for every 10° above °F.................................................... 77
Altitude Deration
Exhaust System
Exhaust Flow at Rated Output 60 Hz.................................. 429 cfm
Exhaust Temperature at Rated Output................................ 1150° F
1% for every 100 m above m................................................... 183
3% for every 1000 ft. above ft. ................................................. 600
Combustion Air Requirements (Natural Gas)
Flow at rated power, 60 Hz ................................................. 144 cfm
Controller.................................................R-200
Governor
Type.................................................................................. Electronic
Frequency Regulation ...................................................Isochronous
Steady State Regulation...................................................... 0.25%
Engine Lubrication System
Type of Oil Pump...................................................................... Gear
Oil Filter............................................... Full Flow Spin-on, Cartridge
Crankcase Oil Capacity....................................................4 U.S. qts.
. 0 v 0 2 / 0 6
G e n S p e c 0 2 0
6-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Standby Generator Sets
Specifications
Figure 1 — Interconnections
Utility In
Transfer Switch
CONTROL PANEL
NEUTRAL
TO
ALTERNATOR
Gen
N1
N2
23
NEUTRAL
N1
N2
23
194
GENERATOR
CONNECTION
BOX
194
CIRCUIT
Load
Out
4- # 14 GA
WIRES TO
GENERATOR
CONNECTION
BOX
186
178
BREAKER
183
178
Battery
Charger
Input
GROUND
TO GENERATOR
120 Volt
+
CONNECTION BOX
Neutral
Grd
To Generator Control Panel
CIRCUIT BREAKER SIZE
FRAME RAIL
KW VOLTS
/
AMPS
200
175
80
LUG SIZE
45
45
45
240 1 Ø
208 3 Ø
480 3 Ø
#6 to 300 mcm
#6 to 300 mcm
#6 to 300 mcm
Ground Level
Concrete Slab
STUB-UP AREA
See Install Dwg for
Dimensions
10. Reverse the procedure to convert back to natural
COLD WEATHER KIT
gas.
For cold climates, optional cold weather kit (part
number 0F6148) is recommended. The kit includes:
11. The Dip switch inside the control panel must be
in the LP or NG position when switching to differ-
ent fuels.
• Battery Warmer
• 4” Junction Box with hardware
• 6 qt. pack 5W-30 synthetic oil (engine)
Figure 6.2 — Reconfigure the Fuel System
RECONFIGURING THE FUEL SYSTEM
NOTE:
All models are configured for natural gas or LP
vapor from the factory.
To reconfigure the fuel system from NG to LP, follow
these steps:
1. Turn the main gas supply off.
2. Remove the carburetor fuel hose from the outlet
port (Port 1) of the demand regulator (Figure
6.2).
3. Remove the brass hose fitting from the outlet port
(Port 1) of the demand regulator.
4. Remove the brass hose fitting with solenoid from
Port 2.
5. Install brass hose fitting into Port 2.
6. Install the brass hose fitting with solenoid into
Port 1.
7. Connect carburetor gas hose to brass fitting.
8. Tighten all clamps and plugs.
9. Make sure fuel supply is of the proper pressure
and type for configuration.
NOTE:
Port 1 is for NG only and Port 2 is for LP vapor
only. No provision for dual fuel has been made.
DANGER
Serious injury or damage may occur if not con-
figured properly. Please consult an Authorized
Service Dealer with any questions.
. 0 v 0 2 / 0 6
G e n S p e c 0 2 0 R e
6-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Standby Generator Sets
General Information
GENERATOR AC LEAD CONNECTIONS
ALTERNATOR POWER WINDING
CONNECTIONS
See “Voltage Codes”. This generator may be rated
at any one of three voltages, either single-phase or
three-phase. The electrical wires in the unit’s AC con-
nection (lower) panel should be installed according to
the number of leads and the voltage/phase required
for the application. If there are any questions regard-
ing lead connection, refer to the wiring diagrams at
the back of this manual.
3-PHASE ALTERNATORS
The generator is designed to supply 3-phase electri-
cal loads. Electric power is produced in the alterna-
tor power windings. These windings were connected
at the factory to the main circuit breaker with a “Y”
configuration as shown in Figures 7.2 and 7.3.
Voltage codes apply to the type of stator assembly
installed on a particular generator.
The rated voltage between circuit breaker terminals
E1-E2, E1-E3 and E2-E3 is either 480V or 208V
depending on the model.
FOUR-LEAD, SINGLE-PHASE STATOR
The rated voltage between each circuit breaker termi-
nal and the neutral point 00 is either 277V or 120V
depending on the model.
Four-lead generators (see Figure 7.1) are designed to
supply electrical loads with voltage code “A” (240V,
1-phase, 60 Hz). Electrical power is produced in the
stator power windings. These windings were con-
nected at the factory to the main circuit breaker as
shown in Figure 7.1.
Figure 7.2 — Stator Power Winding
Connections - 3-phase, 277/480V (6 Lead)
The rated voltage between each circuit breaker ter-
minal is 240V. The rated voltage between each circuit
breaker terminal and the neutral point 00 is 120V.
S1 E1
Figure 7.1 — Four-lead, Single-phase Stator
INTERNAL
CONNECTIONS
L-L
S6
S4
NEUTRAL
S5
E3 S3
S2 E2
L-N
Figure 7.3 — Stator Power Winding
Connections - 3-phase, 120/208V (6 Lead)
E1
S1
S1
L-L
S4
S6
S4
00 (NEUTRAL)
S5
S3
S2
S6 S5
E3
E2
S3
S2
L-N
. 0 v 0 8 / 0 5
C A C o n n 0 0 1 R e
7-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Standby Generator Sets
Installation
PRIOR TO INITIAL START-UP
INSTALLATION
Refer to the separate “Installation Guide QT Product
Line” supplied with the unit.
Prior to initially starting the generator, it must
be properly prepared for use. Any attempt to
crank or start the engine before it has been
properly serviced with the recommended types
and quantities of engine fluids (oil, coolant, fuel,
etc.) may result in an engine failure.
PREPARATION BEFORE START-UP
The instructions in this section assume that the
standby generator has been properly installed, ser-
viced, tested, adjusted and otherwise prepared for
use by a competent, qualified installation contractor.
Be sure to read the “Safety Rules”, as well as all other
safety information in this manual, before attempting
to operate this (and related) equipment.
ENGINE COOLANT
Have the engine cooling system properly filled with
the recommended coolant mixture. Check the system
for leaks and other problems. See “Specifications”
and “Coolant” sections.
Before starting the generator for the first time, the
installer must complete the following procedures. For
follow-up maintenance information and/or service
intervals, please refer to the “Maintenance” section
and the “Service Schedule”.
BELT TENSION
Check-the engine-fan belt tension and condition prior
to placing the unit into service and at recommended
intervals. Belt tension is correct when a force of
approximately 22 pounds (10 kg), applied midway
between pulleys, deflects the belt about 3/8- to 5/8-
inch (10 to 16 mm).
TRANSFER SWITCH
If this generator is used to supply power to any elec-
trical system normally powered by an electric utility,
the National Electrical Code requires that a transfer
switch be installed. The transfer switch prevents elec-
trical backfeed between two different electrical sys-
tems. (For additional information, see the applicable
transfer switch manual for this unit.) The transfer
switch, as well as the generator and other standby
components, must be properly located and mounted
in strict compliance with applicable codes, standards
and regulations.
ELECTRICAL SYSTEM
Make sure the generator is properly connected to an
approved earth ground.
Make sure the generator battery is fully charged,
properly installed and interconnected, and ready for
use.
FUEL SYSTEM
Check to ensure that there are no loose electrical con-
nections. Restrain any loose wires to keep them clear
of any moving generator set components.
Make sure the fuel supply system to the genera-
tor (a) delivers the correct fuel at the correct pres-
sure and (b) is properly purged and leak tested
according to code. No fuel leakage is permitted. See
“Specifications” for more information.
INITIAL INSPECTION FOR QT GENSET
STARTUP
GENERATOR SET LUBRICATION
Inspect for the following.
Check the engine crankcase oil level before operating
and add oil to the proper level – the dipstick “FULL”
mark. Never operate the engine with the oil level
below the dipstick “ADD” mark. See “Specifications”
and “Engine Oil Recommendations”.
• Freight Damage.
• Manuals present.
• Fluid Levels ( Oil, coolant, battery, Gear Drive).
• Correct fuel piping.
• Correct muffler installation for QT50, QT70,
NOTE:
QT100 - QT150.
This engine is shipped from the manufacturer
with “break-in” oil. This oil should be changed
after 30 hours of operation.
• Adequate air flow, clearances and ventilation per
installation drawings and applicable codes.
• Correct AC and DC wire size, connections and
grounding. Control and communication wiring to/
from the transfer switch must be run in a separate
conduit from the AC power leads.
• Battery charger connection to 120 VAC.
• Communication wires connected between transfer
switch and generator (HTS only).
Check the oil level in the generator gearbox (if so
equipped) prior to initial use and at the intervals
indicated by the “Service Schedule.” The recom-
mended oil is SAE 90 gear lubricant.
Also, if the engine is equipped with a mechanical gov-
ernor, make sure the governor is properly lubricated
with clean engine oil.
• Unit secured to pad.
. B v 0 1 / 0 6
I n s t a l l 0 0 1 R e
8-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Standby Generator Sets
Installation
• Check voltage at the generator terminals.
START-UP CHECKLIST
• For 3-phase units, check phase rotation at the
transfer switch terminals. The generator phase
rotation must match the utility phase rotation.
• Check for coolant, fuel, oil, and exhaust leaks.
• Close the generators main line circuit breaker.
• Turn the generator set off.
Before working on the generator, ensure the fol-
lowing:
• The AUTO/OFF/MANUAL switch is in the OFF
position.
• Connect the UTILITY supply to the transfer
• The 120VAC supply to the battery charger is
switch.
switched OFF.
• Set the AUTO/OFF/MANUAL switch to AUTO.
• Disconnect utility power before the transfer
switch.
PREPARATION FOR START-UP
Engine should start, transfer to load.
Run at least 15 minutes on generator power.
Make certain all 3-phase loads are functioning
correctly (correct phase rotation).
• Ensure that the 120VAC circuit breaker to the bat-
tery charger is open.
• Remove the fuse from the the control panel. For
the H-100 and R-series: Open the front door of the
control box and remove the 15 Amp ATO fuse in
the lower left-hand corner of the control box.
• Connect the battery cables to the battery. Attach
negative battery cable last.
• Reconnect Utility power
Transfer switch will transfer back to Utility and
engine will shut down within the given time
parameters set up for the specific transfer switch
and controller.
• Close the 120VAC circuit breaker to the battery
• Install all covers, access plates and door panels.
• Put the Owners Manual in a safe and accessible
place.
charger.
• Measure the voltage at the battery before and after
the charger is turned on.
• Make certain the AUTO/OFF/MANUAL switch is in
• Verify all AC electrical connections are tight at the
circuit breaker and transfer switch.
• Visually inspect entire area looking for loose paper,
plastic wrappings, leaves, etc.
the AUTO position.
START-UP INSPECTION
• Check all hoses clamps fittings for leaks or dam-
When a start-up is performed by an Authorized
Service Dealer, a standard three-part form titled
“Start-up Inspection for Standby Power Systems”
(part no. 067377), should be completed by the instal-
lation technician or engineer. See page 1-3 for infor-
mation on locating the nearest Authorized Service
Dealer. The installer should complete the form and
disseminate copies as follows:
age.
• Check all electrical plugs throughout the genera-
tor. Ensure each plug is seated correctly and fully
inserted into its receptacle.
• Verify the AUTO/OFF/MANUAL switch is in OFF
position.
• Open the valve to the engine fuel line.
• Bleed the fuel system of air. (necessary for long fuel
lines).
• Open the generator main line circuit breaker.
• Connect a manometer to the gas line and record
the static pressure. It must be as listed in the
Specifications.
• White copy: Mail to Generac Warranty Department,
P.O. Box 340, 211 Murphy Dr., Eagle, WI 53119-
2062.
• Pink Copy: For service file of installing dealer.
• Yellow Copy: For the customer’s records.
• Insert the fuse into the control panel.
• Move the AUTO/OFF/MANUAL switch to the MAN-
UAL position. The engine should now crank and
start.
. B v 0 1 / 0 6
I n s t a l l 0 0 1 R e
8-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Standby Generator Sets
Operation
GENERATOR CONTROL AND
OPERATION
Do not crank the engine continuously for longer
than 30 seconds, or the heat may
damage the starter motor.
Refer to the appropriate control panel operator’s
manual for this unit.
• Let engine stabilize and warm up.
OPERATING UNIT WITH MANUAL
• Check all applicable instrument and gauge read-
ings. When certain that all readings are correct,
move the transfer switch manual handle to its
STANDBY (GENERATOR) position, i.e., load cir-
cuits supplied by the generator.
TRANSFER SWITCH
If the generator was installed in conjunction with a
transfer switch capable of manual operation only, the
following procedure applies. A manually operated
transfer switch is one that will not provide automatic
start-up and does not include an intelligence circuit.
• Set the standby generator’s main line circuit break-
er to its ON (or CLOSED) position.
• Load circuits are now powered by the standby
generator.
ENGINE START-UP AND TRANSFER
For additional information, refer to the applicable
control panel manual for this unit, as well as any lit-
erature pertaining to the specific transfer switch.
RETRANSFER AND SHUTDOWN
For additional information, refer to the applicable
control panel manual for this unit, as well as any lit-
erature pertaining to the specific transfer switch.
DANGER
To transfer the load back to the utility power source
and shut down the generator, follow these direc-
tions:
The Maintenance Disconnect Switch and the
AUTO/OFF/MANUAL switches (if so equipped)
must be set properly, or the generator will crank
and start as soon as the utility power to the
transfer switch is turned off. Refer to applicable
control panel and transfer switch manuals for
more information.
• Set the standby generator’s main line circuit break-
er to its OFF (or OPEN) position.
• Manually move the transfer switch handle to its
UTILITY (NORMAL) position, i.e., load circuits
connected to the utility.
• Turn ON the utility power supply to the transfer
switch, using the means provided (such as the util-
ity power source main line circuit breaker).
• Let the generator run at no-load for a few minutes
to stabilize internal temperatures.
Do not proceed until certain that utility source
voltage is available to the transfer switch and
the transfer switch main contacts are set to
UTILITY.
Do not attempt manual operation until all power
supplies to the transfer switch have been posi-
• Shut down the generator.
tively turned off, or extremely dangerous - pos-
sibly lethal - electrical shock will result.
OPERATING UNIT WITH AUTOMATIC
Transfer switch enclosure doors should be kept
TRANSFER SWITCH
closed and locked. Only authorized personnel
If the generator has been installed with an automatic
transfer switch, such as an RTS, HTS, or GTS-type
transfer switch, the engine may be started and
stopped automatically or manually.
should be allowed access to the transfer switch
interior. Extremely high and dangerous voltages
are present in the transfer switch.
In order to transfer load from the utility source to the
generator, follow these directions:
NOTE:
Refer to the applicable manual for your trans-
fer switch and to “Transfer Switch Start Signal
Connections”. In addition, please note the dangers
under “Engine Start-up and Transfer.”
• Turn OFF or disconnect the utility power circuit
to the transfer switch, using the means provided
(such as the utility source main line circuit break-
er).
• Set the transfer handle to its UTILITY (NORMAL)
position with load circuits connected to the utility
power supply.
• Set the standby generator’s main line circuit break-
er to its OFF (or OPEN) position.
• Start the generator.
. 0 v 0 8 / 0 5
O p e r 0 0 1 R e
9-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Standby Generator Sets
Maintenance
MAINTENANCE PERFORMED BY
AUTHORIZED SERVICE FACILITIES
COOLING SYSTEM
Air intake and outlet openings in the generator com-
partment must be open and unobstructed for contin-
ued proper operation. This includes such obstruc-
tions as high grass, weeds, brush, leaves and snow.
Before working on the generator, ensure the fol-
lowing:
Without sufficient cooling and ventilating air flow, the
engine/generator quickly overheats, which causes it
to shut down. (See the installation diagram.)
• The AUTO/OFF/MANUAL switch is in the OFF
position.
• The 15A fuse has been removed from the con-
trol box.
The exhaust system parts from this product get
• The 120VAC supply to the battery charger is
switched OFF.
extremely hot and remains hot after shutdown.
High grass, weeds, brush, leaves, etc. must
remain clear of the exhaust. Such materials may
ignite and burn from the heat of the exhaust
system.
EVERY THREE MONTHS
1. Check battery condition.
2. Inspect and test fuel system.
3. Check transfer switch.
4. Inspect exhaust system.
5. Check engine ignition system.
6. Check fan belts.
OVERLOAD PROTECTION FOR ENGINE
DC ELECTRICAL SYSTEM
Engine cranking, start up and running are controlled
by a solid state Engine Controller circuit board.
Battery voltage is delivered to that circuit board via
a 15 amp fuse. These overcurrent protection devices
will open if the circuit is overloaded.
ONCE EVERY SIX MONTHS
1. Test Engine Safety Devices (low oil pressure, low
coolant level, high coolant temperature).
ONCE ANNUALLY
If a circuit breaker opens or a fuse element
1. Test engine governor; adjust or repair, if needed.
2. Clean, inspect generator.
3. Flush cooling system.
melts, find the cause of the overload before
resetting the circuit breaker or replacing the
fuse.
FIRST 30 OPERATING HOURS
CHECKING FLUID LEVELS
1. Change engine "break-in" oil and filter.
CHECK ENGINE OIL
FIRST 100 OPERATING HOURS
Check engine crankcase oil level (Figure 10.1) at least
every 20 hours of operation, or prior to use.
1. Change engine oil and oil filter. After initial
change, service engine oil and filter at 100 operat-
ing hours or six months, whichever comes first.
2. Retorque cylinder head.
• Remove oil dipstick and wipe dry with a clean, lint-
free cloth.
• Install oil dipstick, then remove again.
• Oil should be between FULL and ADD marks.
• If oil level is below the dipstick ADD mark, remove
oil fill cap-. Add the recommended oil to bring oil
level up to the FULL mark. DO NOT FILL ABOVE
THE “FULL” MARK. See “Engine Oil Recommen-
dations” for recommended oils.
3. Retorque intake and exhaust manifold.
EVERY 500 OPERATING HOURS
1. Service air cleaner.
2. Check starter.
3. Check engine DC alternator.
EVERY 800 OPERATING HOURS
1. Retorque cylinder head.
2. Retorque intake and exhaust manifold.
3. Check engine compression.
4. Check valve clearance.
. 0 v 0 2 / 0 6
M a i n t 0 1 0 R e
10-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Standby Generator Sets
Maintenance
Figure 10.1 - Oil Dipstick and Oil Fill Cap
EXERCISE SYSTEM
Start the generator engine at least once every seven
days and let it run at least 20 minutes. See “Weekly
Exercise Cycle”.
Oil Fill Cap
INSPECT COOLING SYSTEM
• Inspect engine cooling system. See “Maintenance
Schedule”.
Oil
Dipstick
• Check hoses for damage, deterioration, leaks, etc.
Correct any discrepancies found.
• Check hose clamps for tightness.
CHECK ENGINE COOLANT LEVEL
See “Checking Fluid Levels”.
PERFORM VISUAL INSPECTION
BATTERY FLUID
Complete a thorough visual inspection of the entire
engine-generator monthly. Look for obvious damage,
loose, missing or corroded nuts, bolts and other fas-
teners. Look for fuel, oil or coolant leaks.
Check battery electrolyte fluid based on the
Maintenance Schedule. Fluid should cover separa-
tors in all battery cells. If fluid level is low, add dis-
tilled water to cover tops of separators. DO NOT USE
TAP WATER IN BATTERY.
INSPECT EXHAUST SYSTEM
Inspect the exhaust system at least once every three
months. Check all exhaust system pipes, mufflers,
clamps, etc. for condition, tightness, leaks, security,
damage.
ENGINE COOLANT
Check coolant level in coolant recovery bottle. See
Specifications.
• Add recommended coolant mixture as necessary.
• Periodically remove radiator pressure cap (only
when engine has cooled down) to make sure the
coolant recovery system is functioning properly.
Coolant should be at bottom of radiator filler neck.
If coolant level is low, inspect gasket in radiator
pressure cap. Replace cap, if necessary. To have
pressure cap tested, contact an Authorized Service
Dealer. Inspect cooling system and coolant recov-
ery system for leaks.
CHECK FAN BELT
• Inspect fan belts every three months. Replace any
damaged, deteriorated, worn or otherwise defec-
tive belt.
• Check fan belt tension. Thumb pressure, exerted
midway between pulleys, should deflect about 3/8
to 5/8 of an inch. Adjust belt tension as required.
INSPECT ENGINE GOVERNOR
Visually inspect electronic governor.
MAINTENANCE OWNER/
OPERATOR CAN PERFORM
DANGER
Do not attempt to adjust the governor. Only
qualified service facilities should adjust the
CHECK ENGINE OIL LEVEL
Refer to “Checking Fluid Levels”.
governor. Excessively high operating speeds
are dangerous and increase the risk of personal
injury. Low speeds impose a heavy load on the
engine when adequate engine power is not
available and may shorten engine life. Correct
rated frequency and voltage are supplied only
at the proper governed speed. Some connected
electrical load devices may be damaged by incor-
rect frequency and/or voltage. Only qualified
service technicians should adjust the governed
speed.
CHECK BATTERY
• See “Checking Fluid Levels”.
• Check battery cables for condition, tightness, cor-
rosion or damage. Clean, tighten or replace as
necessary.
. 0 v 0 2 / 0 6
M a i n t 0 1 0 R e
10-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Standby Generator Sets
Maintenance
Figure 10.3 – Engine Air Cleaner
CHANGING ENGINE OIL
Refer to maintenance performed by authorized service
facilities for engine oil and filter change frequencies.
Air Cleaner
Drain the oil while the engine is still warm from run-
ning. This means warm up the engine, shut it down
and drain immediately as follows:
1. Remove OIL DRAIN HOSE from its retaining
clip.
2. Loosen and remove OIL DRAIN HOSE CAP. Drain
oil completely into suitable container.
3. When all oil has drained, install and tighten OIL
DRAIN HOSE CAP, and re-install into its retaining
clip.
4. Turn OIL FILTER (Figure 10.2) counterclockwise
and remove. Properly dispose of old filter.
(Doors Removed for Clarity)
Figure 10.2 – Oil Filter
SPARK PLUGS
Reset the spark plug gap or replace the spark plugs
as necessary (Figure 10.4).
1. Clean the area around the base of the spark plugs
to keep dirt and debris out of the engine. Clean
by scraping or washing using a wire brush and
commercial solvent. Do not blast the spark plugs
to clean.
2. Remove the spark plugs and check the condition.
Replace the spark plugs if worn or if reuse is
questionable. See the “Service Schedule,” Section
6, for recommended inspection.
Oil
Filter
3. Check the spark plug gap using a wire feeler
gauge. Adjust the gap to 1.07-1.17 mm (0.042-
0.046 inch) by carefully bending the ground elec-
trode (Figure 10.4).
5. Apply light coating of new engine oil to seal of new
oil filter.-Install FILTER and tighten by hand only.
DO NOT OVER TIGHTEN.
6. Remove OIL FILL CAP. Add recommended oil (see
SPECIFICATIONS). DO NOT FILL ABOVE THE
DIPSTICK “FULL” MARK. Crankcase oil capacity
is 4.0 U.S. quarts (3.8 liters).
Figure 10.4 – Setting the Spark Plug Gap
SET PLUG GAP AT 1.07 - 1.17 mm
(0.042 - 0.046 inch)
After refilling the crankcase with oil, always
check oil level on dipstick. NEVER OPERATE
ENGINE WITH OIL BELOW THE DIPSTICK “ADD”
MARK.
7. Start engine and check for oil leaks.
COOLANT CHANGE
CHANGING THE ENGINE AIR CLEANER
Every year, have an Authorized Service Facility drain,
flush and refill the cooling system. See “Specifications”
for cooling system recommendations.
To replace the engine air cleaner, remove the air
cleaner cover and replace the air filter making sure
it is positioned properly before reattaching the cover
(Figure 10.3).
See the “Service Schedule,” for air cleaner mainte-
nance.
. 0 v 0 2 / 0 6
M a i n t 0 1 0 R e
10-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Standby Generator Sets
Maintenance
BATTERY MAINTENANCE
MISCELLANEOUS MAINTENANCE
The battery should be inspected per Section 4.7,
Scheduled Maintenance. The following procedure
should be followed for inspection:
CLEANING THE GENERATOR
Keep the generator as clean and as dry as possible.
Dirt and moisture that accumulates on internal gen-
erator windings have an adverse effect on insulation
resistance.
1. Inspect the battery posts and cables for tightness
and corrosion. Tighten and clean as necessary.
2. Check the battery fluid level of unsealed batteries
and, if necessary, fill with DISTILLED WATER
ONLY. DO NOT USE TAP WATER IN BATTERIES.
3. Have the state of charge and condition checked.
This should be done with an automotive-type bat-
tery hydrometer.
Periodically clean generator exterior surfaces. A soft
brush may be used to loosen caked on dirt. Use a
vacuum system or dry, low pressure air to remove
any accumulations of dirt. The generator is housed
inside an all-weather enclosure, clean the enclosure
with a soft, damp cloth or sponge and water.
DANGER
Once each year have the generator cleaned and
inspected by an Authorized Service Dealer. That
dealer will use dry, low pressure air to clean internal
windings. Parts inside the control console should be
cleaned and inspected at this time as well.
Storage batteries give off explosive hydrogen
gas. This gas can form an explosive mixture
around the battery for several hours after charg-
ing. The slightest spark can ignite the gas and
cause an explosion. Such an explosion can shat-
ter the battery and cause blindness or other
injury. Any area that houses a storage battery
must be properly ventilated. Do not allow smok-
ing, open flame, sparks or any spark producing
tools or equipment near the battery.
Finally, have the insulation resistance of stator and
rotor windings checked. If insulation resistances are
excessively low, the generator may require drying.
BATTERY
All lead-acid storage batteries discharge when not in
use. Refer to specific instructions and warnings that
accompany the battery. If such information is not
available, observe the following precautions when
handling a battery:
Battery electrolyte fluid is an extremely corro-
sive sulfuric acid solution that can cause severe
burns. Do not permit fluid to contact eyes, skin,
clothing, painted surfaces, etc. Wear protective
goggles, protective clothing and gloves when
handling a battery. If fluid is spilled, flush the
affected area immediately with clear water.
• DO NOT use jumper cables and a booster battery
to crank or start the generator engine.
Do not use any jumper cables or booster battery
to crank and start the generator engine. If the
battery has completely discharged, remove it
from the generator for recharging.
• DO NOT recharge a weak battery while it is
installed in the generator. Remove battery from
generator and recharge in a well-ventilated area,
away from fuel vapors, sparks, heat or flames.
• Battery electrolyte fluid is an extremely caustic
sulfuric solution that can cause severe burns. DO
NOT permit fluid to contact eyes, skin, clothing,
painted surfaces, wiring insulation, etc. If any bat-
tery fluid is spilled, flush the affected area with
clear water immediately.
Be sure the AUTO/OFF/MANUAL switch is set to
the OFF position, before connecting the battery
cables. If the switch is set to AUTO or MANUAL,
the generator can crank and start as soon as the
battery cables are connected.
• Always wear safety glasses, rubber apron and
gloves when handling a battery.
Be sure the 120VAC power supply to the battery
is turned OFF, or sparking may occur at the bat-
tery posts as the cables are attached and cause
an explosion.
• Batteries give off explosive hydrogen gas while
charging. The gas can form an explosive mixture
around the battery for several hours after charging.
Any spark, heat or flames can ignite the gas and
cause an explosion which can shatter the battery,
causing blindness or other serious injury.
BATTERY REPLACEMENT
When replacing batteries, use the same number and
the type of battery that follows:
BCI Group No.
CCA
26
525 @ 0 deg. F
NOTE:
The BCI number should be located directly on the
battery.
. 0 v 0 2 / 0 6
M a i n t 0 1 0 R e
10-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Standby Generator Sets
Service Schedule
SERVICE SCHEDULE
30 KW - 150 KW STANDBY GAS ENGINE DRIVEN GENERATOR SETS
The following is a recommended maintenance schedule for standby gas engine driven generator sets from 30kW to
150 kW in size. The established intervals in the schedule are the maximum recommended when the unit is used
in an average service application. They will need to be decreased (performed more frequently) if the unit is used
in a severe application. Use calendar time, from the previous maintenance interval to determine the next required
maintenance interval.
Service Maintenance Interval Information:
The various service maintenance intervals are designated by interval numbers as follows:
1 An early inspection of the generator set to insure it is ready to operate when required and to identify any poten-
tial problem areas.
This inspection may be performed by the end user providing the following safety steps are taken to prevent
the engine from starting automatically without warning:
To prevent injury, perform the following steps in the order indicated before starting any maintenance:
• Disable the generator set from starting and/or connecting to the load by setting the control panel Auto/Off/
Manual switch to the “OFF” position.
• Remove the 15 amp control panel fuse.
• Turn off the battery charger.
• Remove the negative battery cable.
The battery charger must be turned off BEFORE removing the battery cable to prevent an over current condition
from burning out sensitive control panel components and circuits.
Following all maintenance, reverse these steps to insure the unit is returned to standby setup for normal
operation when required.
2 A wear-in service inspection of the generator set to insure it is ready to operate and carry the load when
required, and to identify any potential problem areas.
Performed ONLY ONCE following the first three months or the first 30 hours of operation after purchase of
the unit.
This inspection contains some maintenance tasks which require special tools, equipment, and/or knowledge
to accomplish and should be performed only by an Authorized Service Dealer.
3 An operational inspection of the generator set to insure it is ready to operate and carry the load when required,
and to identify any potential problem areas.
Performed semi-annually or following each 50 hours of operation of the unit.
This inspection contains some maintenance tasks which require special tools, equipment, and/or knowledge
to accomplish and should be performed only by an Authorized Service Dealer.
4 A mid-level inspection of the generator set to insure it is ready to operate and carry the load when required,
and to identify any potential problem areas.
Performed annually or following each 100 hours of operation of the unit.
This inspection contains some maintenance tasks which require special tools, equipment, and/or knowledge
to accomplish and should be performed only by an Authorized Service Dealer.
5 A comprehensive inspection of the generator set to insure it is properly serviced and ready to operate and carry
the load when required, and to identify any potential problem areas.
Performed annually or following each 250 hours of operation of the unit.
This inspection contains some maintenance tasks which require special tools, equipment, and/or knowledge
to accomplish and should be performed only by an Authorized Service Dealer.
. A v 0 9 / 0 5
v S S c h r d 0 0 1 R e
11-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Standby Generator Sets
Service Schedule
Maintenance Level 1
Level 2
Level 3
Level 4
Level5
Tasks
Recom-
mended
Task
Required
Task
Required
Task
Task
Required
Task
Comp. to be done Comp. to be done Comp.
Required
Comp. to be done Comp.
Bi- (Date-
Annually/ Initials) annually/ Initials)
100 hrs. 250 hrs.
to be done (Date- 3 months/ (Date-
monthly/
10 hrs.
Semi-
(Date- to be done (Date-
Initials)
Initials) Break-in Initials) annually/
30 hrs. 50 hrs.
1. Disable the unit
from operating
per the first page
warning.
2. Check the engine
oil level. Adjust
as necessary.
3. Check the engine
coolant level.
Adjust as
necessary.
4. Check the engine
coolant thermal
protection level.
Correct as
necessary.
5. Check the natural
gas delivery
system for leaks
and correct
pressure on gas
engine driven
units. Tighten
connections as
necessary.
6. Check the air
inlets and outlets
for debris. Clean
as necessary.
7. Check the battery
electrolyte level
and specific
gravity if
accessible. Adjust
as necessary.
8. Check the battery
posts, cables,
and charger for
loose
connections,
corrosion, and
proper operation.
Correct as
necessary.
9. Check the unit
wiring for loose
connections,
corrosion, and
damage. Correct
as necessary.
. A v 0 9 / 0 5
v S S c h r d 0 0 1 R e
11-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Standby Generator Sets
Service Schedule
Maintenance Level 1
Level 2
Level 3
Level 4
Level5
Tasks
Recom-
mended
Task
Required
Task
Required
Task
Task
Required
Task
Comp. to be done Comp. to be done Comp.
Required
Comp. to be done Comp.
Bi- (Date-
Annually/ Initials) annually/ Initials)
100 hrs. 250 hrs.
to be done (Date- 3 months/ (Date-
monthly/
10 hrs.
Semi-
(Date- to be done (Date-
Initials)
Initials) Break-in Initials) annually/
30 hrs. 50 hrs.
10. Check the engine
accessory drive
belts and fan
coupling device
if equipped for
correct tension,
wear, weather
cracking, and
damage. Replace
as necessary.
11. Check the engine
valve clearance.
Adjust as
necessary.
12. Visually inspect
the unit looking
for leaks, wear or
damage, loose
connections or
components, and
corrosion. Correct
as necessary.
13. Test the engine
and transfer
switch safety
devices. Correct
and/or adjust as
necessary.
14. Initiate an
automatic start
and transfer of
the unit to site
load and exercise
it for at least 1
hour looking for
leaks, loose
connections or
components, and
abnormal
operating
conditions.
Correct as
necessary.
15. Replace the
engine
accessory
drive belts.
16. Check gearbox
oil level (if
equipped).
17. Change gearbox
oil (if equipped).
. A v 0 9 / 0 5
v S S c h r d 0 0 1 R e
11-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Standby Generator Sets
Service Schedule
Maintenance Level 1
Level 2
Level 3
Level 4
Level5
Tasks
Recom-
mended
Task
Required
Task
Required
Task
Task
Required
Task
Comp. to be done Comp. to be done Comp.
Required
Comp. to be done Comp.
Bi- (Date-
Annually/ Initials) annually/ Initials)
100 hrs. 250 hrs.
to be done (Date- 3 months/ (Date-
monthly/
10 hrs.
Semi-
(Date- to be done (Date-
Initials)
Initials) Break-in Initials) annually/
30 hrs. 50 hrs.
18. Start and
exercise the unit
at full rated load
(use a load bank
if the site load is
not enough) for
at least 2 hours
looking for leaks,
loose
connections or
components, and
abnormal
operating
conditions.
Correct as
necessary.
19. Perform an
engine oil
analysis (send a
sample to a lab
for results).
Change the
engine oil and
filters if the
analysis results
indicate this is
required.
20. Change the
engine oil.
21. Replace the
engine oil filter(s).
22. Replace engine
spark plugs.
Clean and re-gap
or replace as
necessary.
23. Replace the
engine air
filter(s).
24. Perform a 5
minute no-load
operational run
of the unit
looking for any
post service
problems.
25. Return the unit
to standby setup
for operation
when required.
. A v 0 9 / 0 5
v S S c h r d 0 0 1 R e
11-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Standby Generator Sets
Troubleshooting
TROUBLESHOOTING GUIDE
PROBLEM
Engine won’t crank.
CAUSE
1. 15 amp fuse blown.
CORRECTION
1. Replace fuse.
2. Loose or corroded or defective
battery cables.
2. Tighten, clean or replace
battery cables as necessary.
3. Replace contactor.*
3. Defective starter contactor.
4. Defective starter motor.
5. Dead or Defective Battery.
6. 5 amp fuse blown.
4. Replace starter motor.*
5. Remove, change or replace battery.
6. Replace fuse.*
Engine cranks but won't start
Engine starts hard, runs rough.
Engine starts then shuts down.
1. Out of fuel.
1. Replenish fuel.
2. Replace solenoid.*
3. Reconnect wire.
2. Fuel solenoid (FS) is defective
3. Open Wire #14A from Engine Control
circuit board.
4. Spark plugs defective.
5. Door on tank not closed.
4. Clean, regap or replace plugs.
5. Close door on tank.
1. Flame arrestor (air cleaner) plugged or
damaged.
2. Plugged fuel line.
1. Clean or replace as needed.
2. Unclog fuel line.
3. Defective spark plugs.
4. Fuel pressure incorrect.
3. Clean, regap or replace plugs.
4. Confirm fuel pressure to regulator is as
recommended in SPECIFICATIONS.
1. Engine oil level is low.
2. Engine is overheated.
1. Check oil and add oil as needed.
2. Check cooling system for leaks.
3. Replace switch.*
3. Defective Low Oil Pressure Switch
4. Defective Coolant Temperature Switch
5. Defective Control Module circuit board.
6. Coolant Level is Low.
4. Replace switch.*
5. Replace board.*
6. Repair leak - Add coolant.
7. Replace Switch.*
7. Defective Low Coolant Level Switch
AUTO/OFF/MANUAL Switch at OFF, 1. Defective AUTO/OFF/MANUAL switch
1. Replace switch.*
2. Reconnect/close wire.
engine continues to run
2. Open/disconnected wire #15A between
AUTO/OFF/MANUAL switch and Control
Module circuit board.
3. Defective Control Module circuit board
3. Replace board.*
No AC output from generator.
1. Check main line circuit breaker.
2. Check circuit breaker & fuses.
3. Transfer switch set to NORMAL position
4. Generator internal failure.
1. Reset to ON or CLOSED.
2. Reset and replace, if necessary.
3. Set to GENERATOR position.
4. *
5. Thermal circuit breaker open.
5. Auto-reset - Wait 5 min. and
attempt restart.
*Contact the nearest Authorized Dealer for assistance.
. 0 v 0 8 / 0 5 l s b h r t T 0 0 1 R e
12-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Standby Generator Sets
Notes
Download from Www.Somanuals.com. All Manuals Search And Download.
Standby Generator Sets
Notes
Download from Www.Somanuals.com. All Manuals Search And Download.
Standby Generator Sets
Notes
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
3
4
0F3137
0F3188
0F3189
023484N
0F6366B
0F6366A
043180
022264
0C3990
057701
022155
0C2428
0F3824
0A9457
057073
0D5466
0A7822
022237
022241
049226
0C2266
0C2454
022473
022097
0D4698
0F4464
025433
024469
067210A
0D6029
081008
077043J
051713
0F6156
029289
047411
064153B
1
1
1
1
1 / 2
1
2 / 4
2 / 4
2 / 4
REF
4
4
1
1
2
REF
REF
2
2
7
6
8
8
4
REF
1
1
1
1
4
1
1
PAN CB CONN BOX
STAND RH CONTROL
STAND LH CONTROL
BUSHING SNAP SB-2.5-31
XFMR DUAL 120V/16V (FOR 120/240V & 277/480V UNITS)
XFMR DUAL 104V/16V (FOR 120/208V UNITS)
WASHER FLAT M4
3)
A
B
C
D
E
F
G
H
J
UL CIRCUIT BREAKER (JD+LD)
COVER JD/LD CB SHRT STAND
DECAL DANGER HIGH VOLTAGE
CB 0300A 3P 600V S JD6 LL
INSULATOR CIRCUIT BR. JD/LD
SCREW RHM 1/4-20 X 3
WASHER FLAT 1/4-M6 ZINC
WASHER LOCK M6-1/4
NUT HEX 1/4-20 STEEL
0F3329
065469
0D5577
0F2353
022770
022473
022097
022127
0C2454
029289
0F1733
1
1
1
2
4
4
4
4
7
1
1
5 ***
6 ***
7 ***
8 ***
9 *
10
11
12
13
14
15 **
16 **
17
18
19
20
21
23
24
26 *
27
28
29
30
31
32
33
34
35
36
37
WASHER LOCK #8-M4
SCREW PHTT M4-0.7 X 10 ZYC
BLOCK TERM 20A 8 X 6 X 1100V
WASHER LOCK #6
SCREW PHTT #6-32 X 1/2 ZYC
DECAL UTIL SENSE/CUST CONN
DECAL NEUTRAL
SCREW THF M6-1 X 16 N WA Z/JS
TAPE ELEC 1/2 FOAM (AS REQ’D)
DECAL CUSTOMER CONNECT INSIDE
K
L
4)
A
B
C
UL CIRCUIT BREAKER (QN)
COVER QN FRM CB
JUNCTION BLOCK 3/8-16
0F8135
065469
0E7283
0E7284
0E3664
074908
0F8140
036261
0C2454
029289
0F1733
1
1
-
BUS BAR NEUTRAL BLOCK 390
LUG SLDLSS 600/250-1/0 X 1/4-28
WASHER LOCK 3/8
NUT HEX 3/8-16 STEEL
WASHER LOCK M5
DECAL, DANGER HIGH VOLTAGE
CB 0150A 2P 240V S QN2 LL
CB 0175A 2P S QN2 LL 240V
BASE, QN CIRCUIT BREAKER
SCREW HHTT M5-0.8 X 10 BP
COVER QN CB DISH
-
D
E
F
G
H
J
1
2
1
4
7
1
1
SCREW PHTT M5-0.8 X 16 ZYC
SCREW THF M6-1 X 16 N WA Z/JS
WASHER FLAT 1/4-M6 ZINC
WASHER LOCK M6-1/4
BLOCK TERM 20A 6 X 3 X 1100V
DECAL CUST CONN 120V UTILITY
LUG SLDLSS #6-14 X 13/64 CU
SCREW HHTT #10-32 X 3/8 CZ
DECAL GROUND LUG
SCREW HHTT M6-1.0 X 16 ZYC
GROMMET 1.25 X .25 X .75
CONDUIT FLEX 2.0" ID (36” LG)
WASHER FLAT M5
RIVET POP .125 X .275 SS
SCREW THF M6-1X16 N WA Z/JS
TAPE ELEC 1/2 FOAM (AS REQ’D)
DECAL CUSTOMER CONNECT INSIDE
K
*
ITEM INCLUDED WITH HARNESS
** ITEM INCLUDED WITH 0D5464B
*** ITEM QTY. DOUBLES FOR 277/480V
**** ITEM USED WITH 277/480V UNITS ONLY
2
1
1
4
PLATE WIRE SNGL GALV
TAPE ELEC 1/2 FOAM (AS REQ’D)
SCREW HHC M6-1.0 X 16 G8.8
WIRE JUMPER TRANSFORMER (NOT SHOWN)
38 ****
2
1)
A
B
C
UL CIRCUIT BREAKER (ED)
COVER ED CB SHORT STND
DECAL DANGER HIGH VOLTAGE
CB 0050A 3P 480V S ED4 LL
CB 0070A 3P 480V S ED4 LL
CB 0090A 3P 480V S ED4 LL
CB 0125A 3P 480V S ED4 LL
INSULATOR CB S (ED-3P)
0F3328
065469
0D5552
0D5554
0D5556
0D9693
0F0492
048927
023897
022152
022158
0C2454
029289
0F1733
1
1
1
-
-
-
1
4
4
4
4
7
1
1
D
E
F
G
H
J
SCREW RHM #10-32 X 4-1/2
WASHER FLAT #10 ZINC
WASHER LOCK #10
NUT HEX #10-32 STEEL
SCREW THF M6-1 X 16 N WA Z/JS
TAPE ELEC 1/2 FOAM (AS REQ’D)
DECAL CUSTOMER CONNECT INSIDE
K
L
2)
A
B
C
UL CIRCUIT BREAKER (FD)
COVER CB CONN BOX
0F3138
065469
0D5572
0D5573
0D5574
0D5575
0D5576
0F0199
081320
022473
022097
022127
0C2454
029289
0F1733
1
1
1
-
-
-
DECAL DANGER HIGH VOLTAGE
CB 0150A 3P 600V S FD6 LL
CB 0175A 3P 600V S FD6 LL
CB 0200A 3P 600V S FD6 LL
CB 0225A 3P 600V S FD6 LL
CB 0250A 3P 600V S FD6 LL
INSULATOR CB FD FRAME 30MIL
SCREW SHC 1/4-20 X 4.5 G8.8 NZ
WASHER FLAT 1/4-M6 ZINC
WASHER LOCK M6-1/4
-
D
E
F
G
H
J
1
4
4
4
4
7
1
1
NUT HEX 1/4-20 STEEL
SCREW THF M6-1 X 16 N WA Z/JS
TAPE ELEC 1/2 FOAM (AS REQ’D)
DECAL CUSTOMER CONNECT INSIDE
K
L
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
5)
A
B
C
D
E
F
G
H
J
K
L
M
N
P
Q
UL CIRCUIT BREAKER (QJ-2P)
COVER QJ 2P FRM CB
DECAL, DANGER HIGH VOLTAGE
CB 0225A 240V 2P S QJ22
COVER QJ 2P CB DISH
RIVET POP .125 X .275 SS
WASHER FLAT 1/4-M6 ZINC
WASHER LOCK M6-1/4
8)
A
B
C
D
E
F
NEUTRAL BLOCK 390 / 200-400A
BUS BAR NEUTRAL BLOCK 390
SCREW HHC M8-1.25 X 45 G8.8 FT
WASHER FLAT 5/16-M8 ZINC
WASHER LOCK M8-5/16
NUT HEX M8-1.25 G8 YEL CHR
SCREW HHC 1/4-28 X 3/4 G5
WASHER LOCK 1/4-M6 SS
0F8137
065469
0E7994
0F8136
036261
022473
022097
022127
0F8139
0C2454
022237
048527
029289
022770
0F1733
1
1
-
0D5466
039287
022145
022129
045771
045335
083896
0A7822
2
1
1
1
1
2
2
1
1
4
2
2
2
1
7
2
2
1
2
1
G
H
NUT HEX 1/4-20 STEEL
INSUL CB 2P QJ
LUG SLDLSS 600/250-1/0 X 1/4-28
SCREW THF M6-1 X 16 N WA Z/JS
WASHER LOCK 3/8
SCREW SHC 3/8-16 X 3/4 G8.8 NZ
TAPE ELEC 1/2 FOAM (AS REQ’D)
SCREW RHM 1/4-20 X 3
* HARDWARE FOR MTG. CB TERMINAL COVERS IS
SUPPLIED WITH CIRCUIT BREAKERS.
DECAL CUSTOMER CONNECT INSIDE
6)
A
B
C
D
E
UL CIRCUIT BREAKER (225AF)
COVER CB C2-C4 225AF
DECAL DANGER HIGH VOLTAGE
CIRCUIT BREAKERS 200A FRAME
COVER CB DISH 225AF
RIVET POP .125 X .275 SS
SCREW RHM #8-32 X 3-1/4
WASHER FLAT #8 ZINC
WASHER LOCK #8-M4
NUT HEX #8-32 STEEL
TAPE ELEC 1/2 FOAM
DECAL CUSTOMER CONNECT INSIDE
0F4185
065469
0F4165$
0F4186
036261
053640
038150
022264
022471
029289
0F1733
022129
0F8432
0C2454
0F8451
049897
022145
045771
0F8843
W/CB
1
1
REF
1
4
4
4
4
4
2
1
9
1
7
3
9
6
3
F
G
H
J
K
L
M
N
P
R
S
WASHER LOCK M8-5/16
INSULATOR CB 225AF
SCREW THF M6-1 X 16 N WA Z/JS
LUG SLDLSS 300 MCM-6 AL/CU
SCREW SHC M8-1.25 X 20 G8
WASHER FLAT 5/16-M8 ZINC
NUT HEX M8-1.25 G8 CLEAR ZINC
BUS BAR 200A LUG ADAPTOR
TERMINAL COVER CB
T
U
V
W*
3
2
7)
A
B
C
D
E
F
G
H
J
UL CIRCUIT BREAKER (400AF)
COVER CB C2-C4 400AF
DECAL DANGER HIGH VOLTAGE
CIRCUIT BREAKERS 400A FRAME
DECAL CUSTOMER CONNECT INSIDE
SCREW RHM 10-32 X 4
WASHER FLAT #10 ZINC
WASHER LOCK #10
NUT HEX #10-32 STEEL
SCREW THF M6-1 X 16 N WA Z/JS
TAPE ELEC 1/2 FOAM
SCREW SHC M10-1.5 X 25 G12.9
WASHER LOCK M10
BUS BAR CB ADAPTER 225-400 A
LUG SLDLSS 600/250-1/0 X 1/4-28
WASHER FLAT 3/8-M10 ZINC
TERM COVER CB
SCREW HHC 1/4-28 X 1/2 G5
WASHER LOCK M6-1/4
0F4187
065469
0F4166$
0F1733
042419
023897
022152
022158
0C2454
029289
052647
046526
W/CB
0A7822
022131
W/CB
023334
022097
022473
1
1
REF
1
4
4
4
4
7
1
6
6
3
3
3
2
6
K
L
M
N
P
R
S*
T
U
V
6
6
WASHER FLAT 1/4-M6 ZINC
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
0G0056
0F9677
0G0057
1
1
1
RTR-2390--35KD1 CPL
RTR-2390--45KD1 CPL
STR-2390--35AD1 CPL
0F9664
0G0058
1
1
STR 390 45K 2P 1PH DIRECT
STR-2390--35KD1 CPL
0G0184
1
STR 390 45KW 2P 3PH 480V
0G0059
0G0183
0C9708
1
1
REF
REF
REF
1
1
1
1
4
STR-2390--35GD1 CPL
STR 390 45KW 2P 3PH 208V
INSTR HYPOT TEST (NOT SHOWN)
ENGINE ADAPTER
3
4
5
6
7
8
9
SEE ENGINE EV
SEE ENGINE EV
0F5767B
0E5706
FLEXPLATE
ASSY FLYWHEEL CPL W/40MM FAN B
REAR BEARING CARRIER 390/DRCT
ASSY BRUSH HOLDER 390/HSB
GUARD REAR BEARING CARRIER CPL
WASHER FLAT #8 ZINC
0F7874
0F6124
038150
10
11
12
13
14
15
16
17
18
19
20
21
22
23 *
24 *
023454
1
1
4
4
4
4
1
1
4
4
4
4
1
1
KEY WOODRUFF #E
077043F
04576100BU
052646
043123
051779
0A2601
0A2602
0F3398
046526
0C3993
022264
047248
070892
CONDUIT FLEX 1-1/4" (30” LG)
STUD M14-2.0 570 G5 ZINC
WASHER FLAT M14
WASHER LOCK M14
NUT HEX M14-2.0 G8 YEL CHR
SCREW HHC M16-2.0 X 45 G8.8
WASHER FLAT .688 ID X 3.25 OD
SCREW SHC M10-1.5 X 16 G10.9
WASHER LOCK M10
SCREW HHTT M4-0.7 X 25 BP
WASHER LOCK #8-M4
BALL BEARING-45 MM
SLIP RING MACHINED
* ROTOR REPLACEMENT PARTS
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
1.)
A
C2 UNITS
0F9832
1
1
3
SHIELD CONN BOX C2
SHIELD CONTROL STAND C2
SCREW THF M6-1 X 16 N WA Z/JS
0F9832GGS0R
0C2454
B
2.)
A
C3 UNITS
0F9832B
1
1
3
SHIELD CONTROL STAND C3
SHIELD CONTROL STAND C3
SCREW THF M6-1 X 16 N WA Z/JS
0F9832KGS0R
0C2454
B
3.)
A
B
C4 UNITS
0F9832A
0C2454
1
2
SHIELD CONTROL STAND C4
SCREW THF M6-1 X 16 N WA Z/JS
4.)
A
C5 UNITS
0F9832C
1
1
1
1
1
1
3
SHIELD CONTROL STAND C5
SHIELD CONTROL STAND C5
SHIELD CONTROL STAND C5
SHIELD CONTROL STAND C5
SHIELD CONTROL STAND C5
SHIELD CONTROL STAND C5
SCREW THF M6-1 X 16 N WA Z/JS
0F9832D
0F9832EGS0R
0F9832HGS0R
0F9832JGS0R
0F9832FGS0R
0C2464
B
C
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPONENTS INCLUDED IN 0F9696E
1
2
3
4
5
6
7
8
0F1823A
0F3078
0F2606
036261
043181
052777
0F8710B
0F1262
0F1263
0F1264
0F1725C
067680
0E6875A
055911
0F5459
0E3161
0F5090
0F5462
0A5062J
029673
048467
0F1958
082573
0E4494
0F3215
0F6305
0F6305A
0F5886
051713
049226
0F5752F
0F5884
0F5896
0C2265
0C3990
091526
051716
079224
075476
043180
022264
051715
043182
051714
0F3192
0E7403C
0F9785
1
1
1
6
4
7
1
4
1
1
1
1
2
1
1
1
1
1
4
1
1
1
1
1
1
3
1
3
12
12
1
2
2
4
2
4
9
2
2
2
2
2
7
7
1
1
1
ENCL HSB CONTROL PANEL
COVER CONTROL PANEL
HINGE CONTINUOUS H-PANEL
RIVET POP .125 X .275 SS
SCREW PHM M3-0.5 X 10MM
WASHER FLAT M3
ASSY PCB CPL2 CTRLR 3600 RPM
HOLDER, FUSE WICKMANN 178.6150
ADPTR,RH SIDE WICKMAN 178.6191
ADPTR,LH SIDE WICKMAN 178.6192
ASSY PCB 2AMP 12V UL BATT CHGR
ASSY VOLTAGE REGULATOR 60HZ
RELAY, 12VDC C FORM W/DIODE
BLOCK TERM 20A 12 X 6 X 1100V
DECAL CPL CONTROL PANEL FUSES
ASSY PCB BOSCH GOV DRIVER
ASSY PCB SCR BRIDGE
DECAL CPL 3.9L TB1
SPACER 9.5H 3.2 ID
DIO BRIDGE 25A 600V
CIRCT BRK 7 X 1 ETA 46-500-P
PLATE,HARNESS CLAMP
SWITCH RKR DPST 125V SPD
SWITCH RKR DPDT ON-OFF-ON
DECAL, CONTROL HSB
SEAL COVER 3.18X12.7X382
SEAL COVER 3.18X12.7X283
SCREW HHPM M5-0.8 X 12
WASHER FLAT M5
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
WASHER LOCK M5
RES WW 15R 5% 25W QK CONN
SCREW PHTT M3.5-0.6 X 10
SCREW PHTT M3.5-0.6 X 16
SCREW PHTT M4-0.7 X 12 ZYC
SCREW PHTT M4-0.7 X 10 ZYC
SCREW PPHM M5-0.8 X 12 ZNC
NUT HEX M5-0.8 G8 CLEAR ZINC
SCREW PPHM M5-0.8 X 30 SS
SCREW PPHM M4-0.7 X 16
WASHER FLAT M4
WASHER LOCK #8-M4
NUT HEX M4-0.7 G8 YEL CHR
WASHER LOCK M3
NUT HEX M3-0.5 G8 YEL CHR
SUPPORT ANGLE PCB
FUSE ATO TYPE 15 AMP (BLUE)
HARN 3600RPM R200 CONTROL PNL
COMPONENTS INSTALLED PER THIS DRAWING
A
B
C
D
E
F
G
H
J
056739
022287
022473
022097
022127
0F6145
0F2627A
091526
049226
051713
1
2
4
2
2
A/R
1
4
4
RELAY SOLENOID 12VDC PNL MNT
SCREW HHC 1/4-20 X 3/4 G5
WASHER FLAT 1/4-M6 ZINC
WASHER LOCK M6-1/4
NUT HEX 1/4-20 STEEL
SEAL WEATHER .45"DIA
COVER CONTROL PANEL SIDE
SCREW PPHM M5-0.8 X 12 ZNC
WASHER LOCK M5
K
4
WASHER FLAT M5
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
3
4
5
6
7
8
0F9517
052860
052251
052257
052252
052259
052891
0536210410
042909
047411
055414
022447
022097
022473
049813
022261
0F9597A
045764
052212
022302
022131
065852
0F9597
022129
026204
022145
045771
051755
0F9596
1
4
5
5
5
5
5
1
1
1
1
1
1
2
1
1
1
1
4
5
4
1
1
1
1
1
1
1
1
WELDMENT FRAME 2.4L C2
NUT FLANGED HEX M12-1.75
DAMPENER VIBRATION 40 BLUE
SPACER .49 X .62 X 1.87 PWDR/ZNC
DAMPENER VIBRATION
WASHER FLAT M12
SCREW HHC M12-1.75 X 80 G8.8
ASSY WIRE 14.00"
9
SCREW HHC M8-1.25 X 30 G8.8
SCREW HHC M6-1.0 X 16 G8.8
LUG SLDLSS #2-#8 X 17/64 CU
WASHER SHAKEPROOF INT 1/4
WASHER LOCK M6-1/4
WASHER FLAT M6-1/4 ZINC
NUT HEX M6 -1.0 G8 YEL CHR
WASHER SHAKEPROOF INT 3/8
SUPPORT LH ENGINE 2.4L
SCREW HHTT M4-0.7 X 8 BP
SCREW HHC M10-1.25 X 25 G8.8
WASHER LOCK 7/16
WASHER FLAT 3/8-M10 ZINC
SPRING CLIP HOLDER .37-.62
SUPPORT RH ENGINE 2.4L
WASHER LOCK M8-5/16
WASHER SHAKEPROOF INT 5/16
WASHER FLAT 5/16-M8 ZINC
NUT HEX M8-1.25 G8 CLEAR ZINC
SCREW HHC M10-1.5 X 16 G8.8
SPACER ENGINE MOUNT 2.4L
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
0F3408B
0F3411
025507
052647
046526
022131
050331A
050331
038805Y
038804Z
045771
022129
027482
0F3976
0C2454
022145
077483
1
1
BATTERY TRAY C1 CPL
STRAP BATTERY RETAINMENT
WASHER SHAKEPROOF EXT 7/16 STL
SCREW SHC M10-1.5 X 25 G12.9
WASHER LOCK M10
WASHER FLAT 3/8-M10 ZINC
BATT POST COVER RED +
BATT POST COVER BLACK -
CABLE BATT BLACK #1 X 18.00
CABLE BATT RED #1 X 18.00
NUT HEX M8-1.25 G8 YEL CHR
WASHER LOCK M8-5/16
WASHER SHAKEPROOF EXT 5/16 STL
BOOT CONTACTOR CABLES
SCREW THF M6-1 X 16 N WA Z/JS
WASHER FLAT 5/16-M8 ZINC
BATTERY 12VDC 75-AH 26
REF
REF
REF
REF
REF
REF
1
1
REF
REF
REF
1
4
REF
REF
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
3
4
5
6
7
8
9
0G0158
022131
0F9585
046525
052212
0E9868A
0F3216B
0G0115
0G0350
0D3488Q
0F9501
027482
1
3
1
3
ENGINE 2.4L HYUNDAI
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
026925
0A6751
0G0137
0E9747
0F9793
0F9420
0F3903F
042574
0A8584
0C7649
069860E
0G0136
052207
063076
077996
057823
0F9486
045772
045771
043790
057765
061650
022129
022145
057772
052212
0G0114
046526
0F3217
051736
0F9836
051730
0G0145
077996
0C7649
0G0141
0F9792
062963
022131
0D3973
068485
098544
0G0143
046526
049808
049821
022145
022129
042907
0G0344
0G0343
0G0180
0F9723
040976
0G0149
039414
1 (REF)
1 (REF)
1 (REF)
1
1 (REF)
1
PLUG STD PIPE 3/8 STEEL SQ HD
SWITCH HI-TEMP 245D X 3/8NPT
SPACER ALTERNATOR 2.4L HYUNDAI
STARTER 12 VOLT
BRACKET DC ALTERNATOR
ADAPTER ENGINE 2.4L MACHINE
FLEX PLATE 2 POLE 2.4 HYUNDAI
ADAPTOR 1/8NPTF TO 1/8BSPT
SWITCH OIL PRESSURE 10 PSI 2 POL
CLAMP HOSE .38-.87
WASHER FLAT 3/8-M10 ZINC
EXHAUST ADAPTER 2.4L MACH
NUT HEX M10-1.25 G8 YEL CHR
SCREW HHC M10-1.25 X 25 G8.8
ALTERNATOR DC W/OUT PULLEY
PULLEY 117 OD DC ALTERNATOR
BRACKET TENSIONER
OIL FILTER 2.4L HYUNDAI
BELT SERPENTINE 44.13"
ADAPTER 2.4L CRANKSHAFT MACH
WASHER SHAKEPROOF EXT 5/16 STL
1 (REF)
1 (REF)
1 (REF)
1 (REF)
(REF)
1 (REF)
1 (REF)
3
1
1 (REF)
1 (REF)
1
10
11
12
1
HOSE DRAIN ASSY 28"
1 (REF)
1 (REF)
6
1 (REF)
1 (REF)
1
1 (REF)
1 (REF)
1
SPACER ALTERNATOR 2.4L HYUNDAI
SCREW HHC M8-1.25 X 80 G8.8
WASHER FLAT .531ID X 1.062OD
CAP HOSE
CLAMP HOSE #10 .56-1.06
ADAPTER FLEX PLATE PILOT 2.4L
NUT HEX M10-1.5 G8 YEL CHR
NUT HEX M8-1.25 G8 CLEAR ZINC
BARBED EL 90 3/8 NPT X 3/8
ADAPTER M14-1.50 X 3/8 NPT
SCREW HHC M10-1.25 X 65 G8.8
WASHER LOCK M8-5/16
1
2
3
3 (REF)
1
2
6
WASHER FLAT 5/16-M8 ZINC
WASHER NYLON .565
SCREW HHC M10-1.25 X 25 G8.8
SCREW HHC M12-1.25 X 15 G10.9
WASHER LOCK M10
SPACER DC ALTERNATOR PULLEY
SCREW HHC M10-1.5 X 80 G8.8
HARN ENG 2.4L R-200 HYUNDAI (NOT SHOWN)
SCREW HHC M8-1.25 X 60 G8.8
CAP VACUUM 5/32"
CAP ANTIFREEZE RUBBER
CLAMP HOSE .38-.87
O-RING 5/8" ID X 7/8" OD BUNA-N
PLUG WATER PUMP
SCREW HHC M10-1.25 X 30 G8.8
WASHER FLAT 3/8-M10 ZINC
PLUG EXPANSION 16MM TWINREG
SCREW HHC M12-1.25 X 20 G8.8
SCREW HHC M10-1.25 X 16 G10.9
HEAT SHIELD 2.4L HYUNDAI
WASHER LOCK M10
3
1 (REF)
1 (REF)
1
1 (REF)
1 (REF)
1 (REF)
1 (REF)
1 (REF)
1 (REF)
1 (REF)
9 (REF)
4 (REF)
1 (REF)
1 (REF)
1 (REF)
7 (REF)
1 (REF)
3
3 (REF)
5 (REF)
4 (REF)
1 (REF)
1 (REF)
1 (REF)
1 (REF)
4 (REF)
1 (REF)
4 (REF)
WASHER FLAT M12
SCREW SHC M8-1.25 X 30 G12.9
WASHER FLAT 5/16-M8 ZINC
WASHER LOCK M8-5/16
SCREW HHC M8-1.25 X 16 G8.8
GASKET INTAKE COVER HYUNDAI
COVER INTAKE HYUNDAI
GASKET- THROTTLE BODY
INTAKE ADAPTER MACHINED
SCREW SHC M8-1.25 X 20 G12.9
SCREW SHC M14-1.5 X 35 G10.9
SCREW HHC M8-1.25 X 35 G8.8
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
3
4
5
6
7
8
9
0F9529
0F2608
0F5263
046526
059981
022222
0F5050
042568
0F2573
0F4011
1
1
1
5
4
2
1
8
1
1
WELDMENT RADIATOR SUPPORT 2.4L
RADIATOR 598 X 568 X 49 CPL RH
V-BELT 31/64" X 57-3/8"
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53 *
54
55
0F2572
0F5689
0F2862
0F2560
022131
0E2507
035685
0F2561
0C8145
052250
0C7043
043790
022473
0C8146
022097
076749
048031C
031971
0F4496
042911
0F2872
022304
022195
022196
0F8651
045772
0F9867
0F2461
022145
022129
039414
082774
0F9982
0F9781
049813
052644
0C8566
0C2454
090283
080713
045764
065852
069811
069860C
0C7649
1
1
1
1
7
1
4
1
8
2
12
1
16
2
16
1
1
1
1
1
1
2
1
1
9
1
1
1
1
10
1
1
1
1
8
1
ARM TENSIONER
SCREW SHC SHLDR LKG M8X16LG
SPRING TENSION CPL
PULLEY V-BELT 4" FLANGED
WASHER FLAT 3/8-M10 ZINC
PROBE COOLANT LEVEL 3/8NPTF
CLAMP HOSE #28 1.32-2.25
HUB FLEX PLATE
WASHER FLEX (THIN)
TAPE FOAM 1 X 1 (26.75” LG)
DISK FLEX
BARBED EL 90 3/8 NPT X 3/8
WASHER FLAT 1/4-M6 ZINC
SCREW HHC 5/16-24 X 1.124
WASHER LOCK M6-1/4
WASHER LOCK M10
SCREW HHC M10-1.5 X 30 G10.9
SCREW HHC 5/16-24 X 1-1/2 G5
SHIELD RADIATOR C5
SCREW HHC M6-1.0 X 20 G8.8
PULLEY FAN V-GROOVE 9"
FAN COOL 22" DIA 10 BLADE LH
10
TANK COOLANT RECOVERY
CLAMP HOSE BAND 1/4
BEARING #6205 2NSE C3 E SRI2 S
PULLEY 4.5" DIA MACHINED
SCREW HHC M10-1.5 X 30 G8.8
SCREW HHC 1/2-13 X 2" G8
WASHER FLAT 1/2 ZINC
WASHER LOCK 1/2
NUT HEX 1/2-13 STEEL
SCREW HHFC M8-1.25 X 20 W/M6
NUT HEX M10-1.5 G8 YEL CHR
SHAFT FAN DRIVE
RETAINER BEARING
WASHER FLAT 5/16-M8 ZINC
WASHER LOCK M8-5/16
SCREW HHC M8-1.25 X 35 G8.8
KEY WOODRUFF 4 X 19D
HOSE LOWER RADIATOR
HOSE UPPER RADIATOR 2.4L HYUND
NUT HEX M6 X 1.0 G8 YEL CHR
SPACER .5 X 1.5 X .25 STL/ZINC
SCREW HHFC M6-1.0 X 20 G8.8
SCREW THF M6-1 X 16 N WA Z/JS
CAP RADIATOR 13 PSI
BRACKET COOLANT TANK
SCREW HHTT M4-0.7 X 8 BP
SPRING CLIP HOLDER .37-.62
CAP HEX 1/4 NPT BRASS
HOSE OIL DRAIN ASSY 21"
CLAMP HOSE .38-.87
8
2
1
1
1
1
REF.
1
1
* ITEM 53 IS INCLUDED WITH ITEM 64.
BEARING PRESS NOTE:
APPLY LOCTITE 620 BEARING RETAINMENT
COMPOUND TO BEARING SURFACE ON ITEM 37
PRIOR TO PRESSING ITEM 28 ONTO ITEM 37.
ALSO APPLY LOCTITE 620 BEARING RETAINMENT
COMPOUND TO THE OUTSIDE OF 28 PRIOR TO
INSTALLING ITEM 28 INTO ITEM 38.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
3
4
5
6
7
8
9
0E6586
0E0519A
0C8127
052619
022127
062974
0G0190
037561
022097
1
1
1
4
1
1
1
1
1
GASKET BOSCH 32 & 40
ADAPTER CARBURETOR W/PVC CONN
ELEMENT AIR CLEANER
SCREW HHC M5-0.8 X 20 G8.8
NUT HEX 1/4-20 STEEL
STUD TH 1/4-20 X 4-1/2 G2 ZNC
PLATE, AIR CLEANER TOP 2.4L
NUT WING 1/4-20 NYLK
WASHER LOCK M6-1/4
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17 *
026915
075580
0F6390B
039253
022145
022129
045771
0G0180
0E8286
026812
0F8379
0F3869
057823
059057
044118
0D1509
050279
050280
0F9723
0E6586
0E4394
0E4395
057753B
059999G
0E6382B
0F7790E
0E7121
040976
022097
051751
035685
0F6155
047290
030340
042574
028414
040173
2
1
1
2
2
2
2
NIPPLE CLOSE 3/4 X 1.375
FLANGE FUEL INLET
REGULATOR ASSY 2.4L
SCREW HHC M8-1.25 X 20 G8.8
WASHER FLAT 5/16-M8 ZINC
WASHER LOCK M8-5/16
NUT HEX M8-1.25 G8 CLEAR ZINC
GASKET- THROTTLE BODY
STREET EL 45D 1/2NPT BRASS
ELBOW 90D 3/4 NPT
NIPPLE PIPE 3/4NPT X 7
SWITCH, PRESSURE GAS 5" RISE (INCLUDED WITH I/N 3)
CLAMP HOSE #10 .56 - 1.06
HOSE 3/4 ID SAE-30R2 (30.0” LG)
BARBED STR 1/2NPT X 5/8
DECAL INLET PRESSURE
DECAL FUEL INLET NG (NATURAL GAS APPLICATION)
DECAL FUEL INLET LPG (LP VAPOR APPLICATION)
INTAKE ADAPTER MACHINED
GASKET BOSCH 32
ACTUATOR BOSCH 40, GOVERNOR (45KW)
ACTUATOR BOSCH 32, GOVERNOR (35KW)
HOSE 1.5 ID X 2 LG 20R4 (45KW)
CON,TURBO 2.12 X 1.69 (35KW)
VENTURI HOLDER W/32MM ACTUATOR
VENTURI THROTTLE 26MM
O-RING 47.625 ID X 2.38 WIDTH
SCREW SHC M8-1.25 X 20 G12.9
WASHER LOCK M6-1/4
SCREW HHC M6-1.0 X 50 G8.8
CLAMP HOSE #28 1.32-2.25
1 (REF)
1
2
1
1 (REF)
4
1
1
1
1
1
18
19
20
1 (REF)
1
1
1
1
1
1
1
21
22
23
24
25
26
27
28
29
30
31
32
33
34
1
4 (REF)
4
4
2
1
1
1
1 (REF)
1 (REF)
2
HARNESS, CPL FUEL JUMPER
HOSE 3/8 ID SINGLE BRAID (10.0”LG)
HOSE 1/4 ID SAE 30R7 (22”LG)
ADAPTOR 1/8NPTF TO 1/8BSPT
BARBED STR 1/8NPT X 1/4
CLAMP HOSE #5.5 .62-.62
NOTES:
1.
REGULATOR (I/N 3) AS SHOWN IN ILLUSTRATION IS SET UP FOR
NATURAL GAS APPLICATION.
2.
TO CONFIGURE REGULATOR FOR LP VAPOR, SWITCH HOSE BARB,
HOSE CLAMP (I/N 13) AND HOSE (I/N 14) FROM “OUT-1” TO “OUT-2”.
REPLACE PIPE PLUG FROM “OUT-2” TO “OUT-1”. USE PIPE SEALANT
ON HOSE BARB AND PIPE PLUG. MAKE SURE TO KEEP PORTS FREE
FROM DEBRIS DURING RECONFIGURATION PROCESS.
FOR LP VAPOR APPLICATION SUBSTITUE LPG FUEL INLET DECAL P/N
050280 FOR NG FUEL INLET DECAL P/N 050279 (ITEM17).
WHEN SWITCHING FUEL TYPES, THE PROPER DIP SWITCH SITTINGS
MUST BE MADE TO THE CONTROL PANEL. SEE OWNERS MANUAL, FUEL
SECTION FOR MORE DETAILS.
3*.
4 .
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
3
0G0045 (XX)
0C2454
0F5849 (XX)
1
54
2
REAR WRAP C2 CPL
SCREW THF M6-1 X 16 N WA Z/JS
DOOR C2
4
5
6
7
8
9
087233
0E3257
0F5852 (XX)
0F9833 (XX)
0F5851 (XX)
049813
077992
0F9835 (XX)
0F2786
0F2785
0F3364
0F4880
0F5049
0C2634A
022473
022097
022127
0F3072
078115
0F4051
2
4
2
2
1
2
21
1
2
1
1
2
2
1
3
1
RIVET POP .1875 X .450 SS
SCREW TH-FRM M6 W/CAP SHKPRF W
DISCHARGE DUCT LH & RH SIDE C2
FRONT CORNERS C2
DISCHARGE CENTER DUCT C2
NUT HEX M6 X 1.0 G8 YEL CHR
NUT HEX LOCK M6-1.0 SS NY INS
ROOF C2
SLITTER C4
SPLITTER LOWER C4
SPLITTER STINGER C2
SUPPORT SPLITTER LH C2
TAB PULL
10 *
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
ASSEMBLY COVER ACCESS
WASHER FLAT 1/4-M6 ZINC
WASHER LOCK M6-1/4
1
NUT HEX 1/4-20 STEEL
16
48
2
1
2
1
2
2
1
8
2
4
3
1
2
2
2
INSULATION RETAINMENT HANGER
WASHER SELF LOCKING DOME
INSULATION DOOR C2
0F4051A
0F5048
0E5968
INSULATION ROOF TOP
LATCH VISE ACTION 5/16HEX SOCK
GASKET EXTRUDED TRIM (440.64” LG)
INSULATION SPLITTER
INSULATION SPLITTER
INSULATION DUCT
RETAINER INSULATION (820)
INSULATION DUCT SIDES
RETAINER INSULATION (450)
RETAINER INSULATION (740)
INSULATION LOWER SPLITTER
SCREW HHC M6-1.0 X 20 G8.8
ASSY WIRE 14 AWG 34.8" GRN/YEL
WASHER SHAKEPROOF INT 1/4
INSULATION W/ REFL. HT. SHIELD
0F3760K
0F3760E
0F4051C
0F3890B
0F4051B
0F3890
0F3890A
0F3760L
042568
0912970094
022447
0G0266
1
OPTIONAL COMPARTMENT MATERIALS:
ALL P/N’S WITH AN (XX) SUFFIX INDICATE A MULTIPLE MATERIAL AND COLOR OPTION.
USE THE FOLLOWING LEGEND TO IDENTIFY THE CORRECT PART NUMBER:
PART NO.
0XXXXXSN
0XXXXXAN
0XXXXXSG
0XXXXXAG
MATERIAL
STEEL
ALUMINUM
STEEL
COLOR
TAN
TAN
GRAY
GRAY
ALUMINUM
* ALUMINUM ENCLOSURE NOTE: ALL ENCLOSURE PANELS THAT FASTEN TO
THE BASE FRAME MUST BE SECURED USING ITEM 2 & 5 THREAD FORMING
FASTENER AND ITEM 39 LOCK NUT. LOCK NUT IS TO BE INSTALLED AFTER THREAD
FORMING FASTENER HAS PENETRATED THROUGH EXTRUSIONS IN
ENCLOSURE PANELS. ALL ROOF PANELS ARE TO BE SECURED IN THE SAME
MANNER.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
0F9794
0G0113
0F9937
0F2830
0F2962
080762
0E0170B
0C2454
0F9736
0G0007
044149
085917
0D2611
0E8816
047411
022097
022473
036797
024114
022129
088775
1
1
1
1
1
2
1
4
1
1
1
2
2
1
2
2
2
1
2
2
2
MUFFLER 7" X 9" X 18-1/2" 2" IN/OUT
EXHAUST ELBOW 2 1/4 OD 2 1/2OD
BRACKET MUFFLER
MUFFLER BRACKET STIFFENER
MUFFLER STRAP
BOLT U 3/8-16 X 2.62
EXHAUST BLANKET 988MM (C2)
SCREW THF M6-1 X 16 N WA Z/JS
PIPE EXHAUST 2.4L HYUNDAI
DIFFUSER EXHAUST WELDMENT
GASKET EXHAUST RING
WASHER LOCK 3/8 SS
SCREW HHC 3/8-16 X 1-3/4 SS
EXHAUST FLANGE 2" PIPE
SCREW HHC M6-1.0 X 16 G8.8
WASHER LOCK M6-1/4
WASHER FLAT 1/4-M6 ZINC
BOLT U 5/16-18 X 2.25
NUT HEX 5/16-24 STEEL
WASHER LOCK M8-5/16
WASHER FLAT 3/8 SS
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Standby Generator Sets
Warranty
GENERAC POWER SYSTEMS STANDARD LIMITED WARRANTY FOR
HOME STANDBY/LIGHT COMMERCIAL PRODUCT 45kW AND BELOW
For a period of two (2) years from the date of sale, or start-up by Authorized/Certified Generac Power Systems Dealer, or branch thereof, Generac
Power Systems, Inc. will, at its option, repair or replace any part(s) which, upon examination, inspection, and testing by Generac Power Systems or
an Authorized/Certified Generac Power Systems Dealer, or branch thereof, is found to be defective under normal use and service, in accordance with
the warranty schedule set forth below. Any equipment that the purchaser/owner claims to be defective must be examined by the nearest Authorized/
Certified Generac Power Systems Dealer, or branch thereof. This warranty applies only to Generac Power Systems Generators used in "Standby"
applications, as Generac Power Systems, Inc. has defined Standby, provided said generator has been properly installed and inspected on-site by
appropriate personnel. Scheduled maintenance, as outlined by the generator owner's manual, is highly recommended. This should be performed by
an Authorized/Certified Generac Power Systems Dealer, or branch thereof. This will verify service has been performed on the unit throughout the
warranty period.
WARRANTY SCHEDULE
YEARS ONE and TWO — Limited comprehensive coverage on mileage, labor, and parts listed.
• - ALL COMPONENTS
*Start-up and/or On-line Registration, or Registration Card, along with Proof of Purchase, must be performed and/or sent in.
Guidelines:
• Any and all warranty repairs and/or concerns, must be performed and/or addressed by an Authorized/Certified Generac Power Systems Dealer, or
branch thereof.
• A Generac Power Systems, Inc. Transfer Switch is highly recommended to be used in conjunction with the genset. If a Non - Generac Power
Systems, Inc. Transfer Switch is substituted for use and directly causes damage to the genset, no warranty coverage shall apply.
• All warranty expense allowances are subject to the conditions defined in Generac Power Systems Warranty, Policies, and Procedures Flat Rate Manual.
• Units that have been resold are not covered under the Generac Power Systems Warranty, as this Warranty is not transferable.
• Unit enclosure is only covered against rust or corrosion the first year of the warranty provision.
• Use of Non-Generac replacement part(s) will void the warranty in its entirety.
• Engine coolant heaters (block-heaters), heater controls and circulating pumps are only covered during the first year of the warranty provision (If
applicable).
THIS WARRANTY SHALL NOT APPLY TO THE FOLLOWING:
1. Any unit built/manufactured prior to January 1, 2005.
2. Costs of normal maintenance (i.e. tune-ups, associated part(s), adjustments, loose/leaking clamps, installation and start-up).
3. Any failure caused by contaminated fuels, oils, coolants/antifreeze or lack of proper fuels, oils or coolants/antifreeze.
4. Units sold, rated or used for "Prime Power", "Trailer Mounted" or "Rental Unit" applications as Generac Power Systems have defined Prime Power,
Trailer Mounted or Rental Unit. Contact a Generac Power Systems Distributor for Prime Power, Trailer Mounted or Rental Unit definition and warranty.
5. Units used for prime power in place of existing utility power where utility is present or in place of utility power where utility power service does not
normally exist.
6. Failures caused by any external cause or act of God such as, but not limited to, collision, fire, theft, freezing, vandalism, riot or wars, lightning,
earthquake, windstorm, hail, volcanic eruption, water or flood, tornado, hurricane, terrorist acts or nuclear holocaust.
7. Products that are modified or altered in a manner not authorized by Generac Power Systems in writing.
8. Failures due, but not limited to, normal wear and tear, accident, misuse, abuse, negligence, or improper installation or sizing.
9. Any incidental, consequential or indirect damages caused by defects in materials or workmanship, or any delay in repair or replacement of the
defective part(s).
10. Failure due to misapplication, misrepresentation, or bi-fuel conversion.
11. Telephone, facsimile, cell phone, satellite, internet, or any other communication expenses.
12. Rental equipment used while warranty repairs are being performed (i.e. rental generators, cranes, etc.).
13. Overtime, holiday, or emergency labor.
14. Planes, ferries, railroad, busses, helicopters, snowmobiles, snow-cats, off-road vehicle or any other mode of transportation deemed abnormal.
15. Any and all expenses incurred investigating performance complaints unless defective Generac materials and/or workmanship were the direct
cause of the problem.
16. Starting batteries, fuses, light bulbs, engine fluids, and overnight freight cost for replacement part(s).
THIS WARRANTY IS IN PLACE OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, SPECIFICALLY, GENERAC POWER SYSTEMS
MAKES NO OTHER WARRANTIES AS TO THE MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow
limitations on how long an implied warranty lasts, so the above limitation may not apply to purchaser/owner.
GENERAC POWER SYSTEMS ONLY LIABILITY SHALL BE THE REPAIR OR REPLACEMENT OF PART(S) AS STATED ABOVE. IN NO EVENT
SHALL GENERAC POWER SYSTEMS BE LIABLE FOR ANY INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF SUCH DAMAGES ARE A
DIRECT RESULT OF GENERAC POWER SYSTEMS, INC. NEGLIGENCE.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations may not apply to purchaser/
owner. Purchaser/owner agrees to make no claims against Generac Power Systems, Inc. based on negligence. This warranty gives purchaser/owner
specific legal rights. Purchaser/owner also may have other rights that vary from state to state.
Generac Power Systems, Inc. • P.O. Box 8 • Waukesha, WI 53187
Ph: (262) 544-4811 • Fax: (262) 544-4851
Bulletin 0171360SVE / Printed in U.S.A. 7.05
Printed in U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
|